← Bed build

Routing the LED channels

BedGuide

Two shallow grooves along the outside face of each bed wall take flush aluminium LED channels: warm light on top, colour below. The channels sit flush, so nothing stands proud into the half inch to the wall. Every number here comes from the same model as the build page.

The size

Channelflush U aluminium profile, about 17 x 8 mm, milky diffuser, end caps
Groove11/16 in wide, 5/16 in deep, two per board
Whereoutside face; centres 3 1/8 and 2 1/2 in up from the board's bottom on every board, so they make one line round the frame: 1 3/8 and 2 below a 1x5's top, 5 3/8 and 6 below the head board's
How much33 ft of channel, both rows. It comes in 1 m (39 in) lengths: buy 12, the long runs take two joined end to end
warm groove, centre 1 3/8 below the topRGB groove, centre 2 below the topboard top11 11/161 11/162 3/83/4 boardoutside face (toward the wall or the slot)

The runs

Each channel runs only where the board is full height. Rout full length anyway; the notches remove the rest.

BoardLengthChannel runsRun
Head board (driver)60 3/40 to 60 3/4 from its back end60 3/4
Foot board (passenger)60 3/40 to 60 3/4 from its back end60 3/4
Back 1x5 (outer)78 3/80 to 78 3/8 from its driver end78 3/8

Tools

Router with an edge guide; 1/2 in straight or upcut spiral bit; clamps; calipers; 180 grit; a drill with a 3/16 bit; a scrap of the same poplar to test on.

1Get the channel first

Measured: each channel is 16.93 mm wide, so the one groove for both is 1 11/32 in. Height with the cover still to caliper; the plan assumes 5/16 in. Make the depth exactly that, so the cover ends flush with the wood.

2Rout before the notches

Rip each board to height, rout the grooves, then cut the notches. Wherever there is a notch, it takes the groove away cleanly with it, so you rout every board full length and never have to start or stop a groove.

3Set up

Board flat on the bench, outside face up, the top edge toward you, clamped at both ends with the clamps below the surface. A router with an edge guide riding on the board's top edge. A 1/2 in straight or upcut spiral bit.

4Test on scrap

Run both grooves on an offcut of the same board first. Press the channel in: it should need a thumb, not a mallet, and sit flush. Adjust the guide until it does.

5Warm groove

Guide set so the bit's near edge is 1 in from the top edge. First pass 1/8 deep, second pass to 5/16. Then move the guide out so the far edge lands at 1 11/16 and repeat: two passes widen the 1/2 in bit to 11/16.

6RGB groove

Same again with the edges at 1 11/16 and 2 3/8. That leaves 0 of wood between the grooves and 1 above the top one.

7Feed direction

Push the router so the bit's rotation pulls the guide against the board's edge: with the top edge toward you, feed left to right. Steady speed; poplar burns if you stop.

8Clean up

Knock the fuzz off the groove edges with 180 grit on a block. Blow the dust out.

9Cut the notches

Now the notches, drilling each inside corner with the 2 in Forstner first. The grooves run out into the notches; that is where each run ends.

10Wire holes

At the start of each run, the end nearest a back corner, drill a 3/16 in hole from the groove bottom straight through to the inside face. The strip's wires go through it and down behind the mattress to the feed hole in the deck.

11Later: the channels

When the lights go in: a thin bead of clear silicone in each groove, press the channel in, strip in, diffuser snapped on, end caps. Warm in the top groove, RGB below.