TopeLeave about Dec 1
← Bed build 1/16
← Bed platform

Bed build

Assembly16 steps

Rails, struts, veneered boards, deck, lights, headboard. The diagram follows the step you are on.

Cut list10 parts

Inches. Crossways lengths follow H1.

partstockqtylength
Struts1 1/2 x 3 tube, flat4full frame width, on the Happijac rails
Head board1x10 ripped to 8 1/2 poplar1driver side, on the rails, from the back 1x5 to the front; notched under for the 4 struts, and 2 in at each top corner
Foot board1x5 poplar1passenger side, on the rails; notched under for the struts, and at the motor
Back 1x51x5 poplar, 4 1/2 tall1on the rails where the old back board is, flush with the rail ends; notched at the motor end; veneer the bottom and top edges
Inner back wall1x5 ripped to 3 1/2 poplar1on the deck, between the head and foot boards, 1 1/4 in in front of the back 1x5; notched at the motor
Spacer strip1/2 ply or poplar11 1/8 wide, on the back strut behind the back panel: the slot floor, level with the deck
Front1x6 white oak ripped to 4 1/21rip to 4 1/2 tall, 1/2 roundover on top
Deck1/2 ply319 7/8 / 19 7/8 / 19 7/8 deep, between the head and foot boards
Headboard1/2 ply113 1/2 tall
Hingematte black continuous, 1-1/16 x 12 in (bought 4)4four short hinges spaced along the headboard
Hardware and supplies30 lines
forwhatqty
Struts to rails1/4-20 x 3/4 bolts up through the rail and the strut's bottom wall, washer under the head, nut inside tightened through the access hole, anti-seize. BOUGHT 2026-09-30: black steel hex bolts with split lock washers, an interim set; swap to black stainless with nylock nuts (McMaster, Bolt Depot). One per strut end8
a 1/2 in access hole in the strut's top wall above each bolt, for the socket; the deck covers them8
Corners1 1/2 in black corner braces, 2 inside each corner, #8 x 5/8 flat-head wood screws into both boards (hook-on bed brackets rattle loose in a truck)8
Board brackets1 1/2 in black corner braces on the inside faces, down onto the deck~16
Back 1x5small black angle, about 1 x 1, in the slot floor: upright leg on the 1x5's inside face, flat leg on the strut top. #8 x 5/8 into the poplar, #10 self-drilling into the strut (Tef-Gel)3
Slot cornerssmall black angle inside each back corner of the slot: head or foot board to the 1x52
#8 x 5/8 flat-head wood screws into the 3/4 poplar: braces and corners. Pilot 3/32; comes apart a handful of times, and a worn hole just moves the brace 1/4 in~80
#8 x 1/2 flat-head wood screws into the 1/2 ply deck. Not longer: anything over 1/2 comes through the office ceiling~40
Front board#10 x 1 1/4 stainless countersunk sheet-metal screws + cup washers, into the front strut (through the 3/4 oak and the 1/8 strut wall)9
Deck#10 x 3/4 stainless flat-head sheet-metal screws~40
Headboardmagnetic catches, to hold it folded for travel2
locking lid supports (Everbilt lid support hinge kit, matte black), one each end: hold it upright while you sleep2
EverywhereTef-Gel on steel into aluminium; felt tape on strut tops
BoardsBOUGHT 2026-09-30 at Crosscut Hardwoods: poplar 1x10 S4S 8 ft (head, rip to 8 1/2); poplar 1x6 S4S 24 ft (foot and both back boards, rip to 4 1/2); white oak 1x6 S4S 9 ft (front, rip to 4 1/2); 1/2 in white oak S2S 7.5 sq ft (ceiling strips)
Veneerpaper-backed white oak, 10 mil, 4x8, plus a spare 2x81
Gluesolvent-based contact cement, e.g. DAP Weldwood Original1 qt
ToolsJ-roller, sharp knife, 120 and 180 grit, acetone
Finishwater-based polyurethane, satin (Varathane Ultimate or General Finishes High Performance): never solvent-based over contact-cemented veneer1 qt
Warm stripBTF FCOB 12 V 2700K CRI 90+, IP3017 ft
RGB stripBTF FCOB RGB 12 V 10 mm, IP3017 ft
Channelsflush U aluminium profile, 16.93 mm wide (measured), black, frosted diffuser, end caps33 ft
Router1/2 in straight bit and a two-rail jig (or an edge guide), for the groove
Pucksslim 12 V surface-mount, 3/8 in or thinner, 2700-3000K4
ControllerQuinLED An-Penta-Deca (ESP32, 15 fused PWM channels, ESPHome): colour 3 + warm 1 + pucks 1, 10 spare; in the control box, 3D-printed cover1
Cable9+ core continuous-flex (drag-chain rated) cable, 18 AWG: strips 5, pucks 2, the two Sirocco fans 2 (if they mount on the deck)~10 ft
Cable chainsmall plastic drag chain, about 10 x 15 mm inside, bend radius 18 to 20 mm, end brackets: fits the 1 1/2 in column slottravel + 1 ft
Control boxin the upper cabinet: controller, fuses, a physical switch; 14/2 from the bus
Dimmer at the beda wireless button for the controller (e.g. Shelly BLU Button), stuck up in the lounge: no wires1
Fusesone 15 A on the controller's feed from the 12 V bus (the Deca fuses each channel)1
Junctionsmall box under the deck at the back foot corner, Wago 221 lever nuts1

Prepsteps 1 to 6

    1. Measured 2026-09-30: 79 3/8 in between the Happijac columns, so the frame is 78 3/8 in wide with 1/2 in to each column.
    2. Mattress 78 x 60 x 6. Inside the frame it gets 76 7/8 x 58 3/4: squeezed a little both ways, which memory foam takes.
    3. At the back, two boards and a slot. Outside: a 1x5, 4 1/2 tall, on the rails where the old back board is, flush with the rail ends: the edge you see from below. Inside: a 1x5 ripped to 3 1/2, standing on the deck 3 in off the rear wall, clear of the drive shaft.
    4. Between them a slot 1 1/4 wide, 2 1/2 deep to the top of the 1x5. Its floor is a 1 1/8 spacer strip on the back strut, level with the deck. Phone, Kindle, mask. The strut and the rails do not move: no new holes.
    5. At full up the drive shaft sits over the slot, about 6 1/16 in up. Nothing in the slot may stand taller than about 3 9/16 in from its floor.
    6. The front does not move, so the mattress gets 58 3/4 front to back: squeezed 1 1/4 in. The head and foot boards run 60 3/4 from the 1x5 to the oak front and close the slot's ends.
    Caution Bed fully up, the ceiling is 9 1/2 in above the bed bottom. Fold the headboard before raising it.
    Drawings
    1. 4 struts at the cut-list length: the full frame width, so they run through the notches under the head and foot boards.
    2. File the ends smooth.
    1. Head: 1x10 ripped to 8 1/2 poplar on the rails, 8 1/2 tall, 1/2 in above the mattress: it carries the headboard. Foot: a 1x5 on the rails. Back: two 1x5s, the outer one on the rails, the inner wall on the strut. Front: 1x6 white oak ripped to 4 1/2, 4 1/2 tall. The mattress stands above the 1x5s; they locate it, they don't wall it in.
    2. Notch head and foot UNDERNEATH for the struts: 3 in long by 1 1/2 deep, one at each strut; the back one is 1 long, at the very end.
    3. Notch the 1x5's passenger end 11 in long, down to 4 1/8 in: full height it clears the motor plate by only 1/8.
    4. Notch head and foot at the FRONT end: 2 in long, down to 6 1/4 in above the bed bottom (the spools).
    5. Notch the head board's BACK end, driver side, the same: 2 in long, down to 6 1/4 in (the drive shaft end). Size assumed: check it at full up.
    6. Passenger side, back corner, the motor: notch the foot board's BACK end 5 3/4 in long, and the back board's FOOT end 9 in long, both down to 4 1/8 in (the motor plate).
    7. Round the inside corner of every notch with a 1 in radius. It looks meant, and it stops cracks.
    8. Rout ONE LED groove along the outside face of each board on the rails, 1 11/32 wide, from 2 5/32 to 3 15/32 up from its bottom: the warm and RGB channels side by side in it, one line round the frame. Front: 1/2 in roundover on top.
    Drawings
    1. Scuff the aluminium with 120 grit, wipe with acetone.
    2. Contact cement on both surfaces. Wait until it no longer sticks to a knuckle.
    3. Wrap the bottom (the 3 in face) and both sides in one piece. Leave the top bare.
    4. Stop the bottom 2 in short of each end: that part sits on the Happijac rail.
    5. Roll hard from the middle out. Trim with a knife, sand the edges with 180.
    Tip Solvent-based cement. The water-based kind lets go in a hot van.
    1. Poplar boards: veneer the top edges and the notches; the mattress hides the inside faces and the wall hides the outside.
    2. White oak front: no veneer and no stain. Same species as the veneer, so the same clear finish matches it.
    3. Deck underside is the office ceiling: sand and finish it like furniture.
    4. 3 coats of satin poly on everything, 320 grit between.
    1. Mark the 4 pucks off the struts as installed: halfway along the gap between the two back struts and between the two front struts.
    2. Across: a quarter of the deck length in from each end (19 1/4 in). From below they make a near-square grid.
    3. Drill a 3/8 in wire hole at each. In the deck TOP, rout a 1/4 in groove from each puck straight back, parallel to the head board, to a cross groove 4 in in front of the inner wall.
    4. The cross groove runs along the back, from the passenger-side puck line to 3 in from the head board. One 1/2 in hole down there, over the junction box. Nothing runs under the deck: it is the office ceiling.
    5. Where a groove crosses a deck seam, leave a little slack loop so a panel can lift. Keep the deck screws out of the groove lines.
    6. Drill a 3/8 in hole through the deck just inside each back corner, for the strip feeds.
    Drawings

Framesteps 7 to 8

    1. Lay the struts flat across the two black rails: the back one where it is now, tight in front of the 1x5, the front one flush with the deck's front edge, the middle two under the deck seams.
    2. Drill a 1/2 in access hole in each strut's top wall above every rail hole (step bit). Bolt each end: 3/4 in button-head up through the rail and the strut's bottom wall, nylock nut inside, tightened through the access hole. Anti-seize on every bolt: steel, stainless and aluminium all touch here.
    3. Diagonals equal within 1/8 in before the last screws go in.
    Tip Drill through the veneer; it does not mind.
    Drawings
    1. Full travel, slowly. At the top, check the struts clear the spools, the motor and the drive shaft.
    2. Fix any rub now, before anything is on top.
    Drawings

Deckstep 9

    1. Three sheets, 76 7/8 long to fit between the head and foot boards, seams on the middle struts.
    2. Felt tape on the strut tops. Screw into every strut about every 12 in, 3/8 in from the seam edges.
    Tip Deck and struts screwed together are what make the bed stiff. Don't travel with it loose: the lift bounces.
    Drawings

Boardssteps 10 to 11

    1. The 1x5 on the rails, flush with the rail ends, tight against the back strut, full width. 3 small angles in the slot floor hold it to the strut.
    2. Head and foot boards down onto the rails, the struts through their notches, from the 1x5 to where the oak front goes. They close the ends of the slot; a small angle in each back corner ties them to the 1x5.
    3. The spacer strip on the back strut behind the back panel, then the inner back wall on the deck, between the head and foot boards, 1 1/4 in in front of the 1x5. It all unscrews.
    4. Two corner braces inside every corner, one high, one low, #8 x 5/8 wood screws into both boards, 3/32 pilots. Comes apart with a screwdriver; nothing to rattle loose on a rough road.
    5. Corner braces from each board's inside face down onto the deck: #8 x 5/8 into the board, #8 x 1/2 into the deck (a longer one comes through the ceiling). The mattress hides them.
    Caution No glue anywhere: it all comes apart.
    Drawings
    1. Across the front, covering the front strut and the deck edge, standing 2 1/2 in above the deck.
    2. Corner braces into the head and foot boards at the corners, and countersunk stainless screws with cup washers into the front strut every 8 in.
    3. With 3 in of aluminium behind it, it takes being climbed over and sat on every day.
    Drawings

Lightssteps 12 to 14

    1. A thin bead of clear silicone in each groove, press the channels in flush.
    2. Warm strip in the top channel, RGB in the lower one. Diffusers on. The notches break the runs; feed across them on the inside face.
    3. Each run starts at a back corner: feed wires come up through the deck hole. They meet the pucks at the junction in step 13.
    4. Nothing stands proud into the 1/2 in gap to the columns.
    Tip Bare IP30 strips: the channel is the heatsink.
    Drawings
    1. Screw the 4 pucks under the deck at the holes, wires up through.
    2. Lay the wires in the grooves to the cross groove and along it to the driver back corner, tape over them, and take them down through the one hole.
    3. Junction box under the deck at the driver back corner, right under that hole. Wire it as the schematic: pucks on their own pair.
    Drawings
    1. From the junction, out at the back corner on the driver (head) side, into the slot between the back Happijac column and the wall.
    2. The slot is 1 1/2 in and clear (measured 2026-09-30): a small drag chain in it, hanging in a U that follows the bed. Fixed end bracketed in the slot at mid-travel; moving end bracketed to the bed at the corner.
    3. Turn the chain so its U runs along the slot's depth, not across its 1 1/2 in width.
    4. From the fixed end: down to the floor, along inside the lounge behind the bench, and up into the control box in the upper cabinet.
    5. Controller, fuses and a switch in the control box. A wireless button stuck up in the lounge dims them from the bed, no extra wiring.
    Caution Cycle slowly and watch the loop the whole way: nothing may touch the trolley or the chain drive.
    Drawings

Finishsteps 15 to 16

    1. 1/2 ply, white oak veneer on both faces (one face alone cups it), Rubio oil like the struts and the front. About 1/2 thick.
    2. 55 3/4 long, 13 1/2 tall: 14 in above the mattress. It stands on the head board's full-height stretch, clear of the front notch.
    3. Stand it on the head board. Hinge knuckle on the inboard top edge: it can only fold forward onto the mattress. Leaning on it with a pillow presses it onto the board.
    4. Plane the head board's top 4 degrees, low on the wall side, under the headboard. It then rests leaning back a little, and gravity holds it against its stop.
    5. A locking lid support at each end, inboard, from the headboard to the head board: it clicks rigid when upright, so it cannot fold onto you in the night. Press the elbow to fold it.
    6. Magnetic catches hold it folded for travel.
    Caution Fold it before the bed goes up: upright it hits the ceiling.
    Drawings
    1. Mattress on, headboard folded, every light on, full travel.
    2. Re-snug the bolts after a week of driving.
Notes8
  • Trolleys drawn at 10 and 50 in, assumed.
  • Lights: strip wattage (10 W/m each colour), puck size, groove size and the 8 ft cable are assumptions. With about 1 in to the wall the channels face the wall close up: expect a soft halo round the bed, not a tall wash.
  • Cable slot: 1 1/2 in wide and clear, measured. Still to measure: its depth (the chain's U needs about 2 1/4 in) and the bed's full travel (sets the chain length).
  • Struts flat, not on edge like the design page: the bed sits 1 1/2 in lower, but one adult kneeling mid-span bends a strut 7/16 in instead of 1/8. Still 5x strong enough. If it feels bouncy, the spare fifth tube becomes a fifth strut.
  • How to rout the LED grooves, step by step: Routing the LED channels.
  • Boards screw to the deck with corner braces: no glue, nothing into the Happijac rails except the struts, and the whole bed comes apart. Wood screws take being backed out a handful of times; a worn hole just moves the brace 1/4 in.
  • As built, measured 2026-09-30: struts screwed onto the Happijac's own L rails, deck on the struts; the head and foot boards stand on the rails, notched over the struts. 79 3/8 in between the columns. The rail's section (drawn 2 x 2) is assumed.
  • Back: the 1x5 is where the old back board was, about 1 in off the wall; the back strut is assumed tight in front of it, 3 in wide. The drive shaft is drawn 7/8 across at 2 in off the wall: measure it, it sets how tall things in the slot can be.
  • Headboard is 3/4 thick, not the design page's 1 1/4, so it stays out of the track band.
  • Frame boards are poplar with veneered top edges; the front is solid white oak, not the design page's layout.