TopeLeave about Dec 1

Systems / Water / Shower / Cab slider in 3D

Shower

wedi floor and walls, the swing door to the kitchen, the slider to the cab, microcement.

D2, every part, shut and parked.

The cab slider

D2 on its own, from the plan's numbers. It covers the passthrough to the cab: a 20 11/16 in door of 12 mm Baltic birch hanging from a track on the shower side of the cab wall, sliding 20 11/16 toward the driver wall to open. Its bottom runs 1/4 above the cable box, which is its curb.

Pull apart spreads every part out with its name. Open doors slides it to parked. Tap any part for what it is.

The top of the door

The passthrough is a hole cut through the cab plywood, 39 tall, and the opening is all of it (Jeff, 2026-10-12: no head): 35 1/2 clear above the cable box. The door laps the hole's top by 3/4, and the track hangs above the hole from a bracket screwed through the finished wall into the factory cab plywood. Hover or tap a number.

CABSHOWERTOP OF THE DOOR, IN SECTION12345678910111213
  1. 1Factory cab plywood, above the passthrough hole
  2. 2The opening, through to the cab: the hole's full height, 39 (no head)
  3. 3The hole's top edge: the plywood's cut edge, sealed, microcement wrapped round it
  4. 41/4 wedi on the cab wall's shower face, stopping at the hole's edge
  5. 5Microcement: the finished wall
  6. 6Cab side: a stainless fender washer and a nylock (or a cap nut, for looks) on each bolt
  7. 7The track bracket: a bent stainless angle (or Husky's own face-fix bracket). Its leg screws flat to the finished wall, above the hole
  8. 8Bolts: 1/4-20 stainless right through the bracket, a sleeve in the wedi and the cab plywood; sealant round each sleeve
  9. 9Its flange: the track screws up into it
  10. 10Husky box track, aluminium, open at the bottom
  11. 11Hanger: rolls in the track, bolts down into the door's top rail
  12. 12Hardwood top rail on the door: gives the hanger bolts something to bite
  13. 13The door: 12 mm Baltic birch, 20 11/16 wide, microcement both faces, hanging on the shower side, lapping the hole's top by 3/4

The same cut, full height:

CABSHOWERFULL HEIGHT1234567
  1. 1Cab plywood above the hole: the bracket screws into it
  2. 2The track and its bracket, on the finished wall
  3. 3The door, 36 tall, shut over the opening
  4. 4The opening through to the cab: 19 3/4 wide, 35 1/2 tall above the box
  5. 5The sweep along the door's bottom edge, brushing the box top
  6. 6The cable box: 3 1/2 tall, along the whole cab wall, also the door's curb. The door hangs 1/4 above it
  7. 7The shower floor

From above

At about 20 in up: the post and infill closing the rest of the hole, the door shut and parked. Depth (cab to shower) is drawn stretched so the layers read.

19 3/4 clearCABSHOWERFROM ABOVE123456789
  1. 1Wardrobe
  2. 2Jamb seal: the shut door's wardrobe edge closes against it
  3. 3The door, shut: 20 11/16 wide, lapping the opening each side
  4. 4The opening through to the cab
  5. 5Infill: one piece of 3/4 ply, 5 11/16, its edge the opening's driver side
  6. 6BG1 guide: keeps the door's bottom from swinging, screwed to the infill
  7. 7The door, parked: slid toward the driver wall, over the cab wall's wedi
  8. 8Travel latches, shut and parked: it must not slide on the road
  9. 9Cab wall: wedi and microcement beside the opening

Its parts 11

have it

Cable box and D2 curb, the whole cab wall: 2x4 blocks, a 1/2 ply top, wedi on its face and top

have it
ready to order

wedi building panel 1/4 in, 48 x 60 (US8000013)

stock
TBD

Microcement: CimentART Aqua shower system

stock
TBD

Door seals, EPDM bulb (D1 and D2)

stock
have it

D2 fill strip behind the wardrobe, 3/4 ply

have it
ready to order

D2 infill, the doorway's driver edge, 3/4 ply

cut from stock
ready to order

Husky PC100/200 hangers, clip stops, BG1 guide

stock
ready to order

Husky track, aluminium, 6 ft (cut to 41 1/2)

stock
ready to order

D2 leaf, 12 mm Baltic birch (the D1 sheet offcut), hardwood top rail

have it
have it

D2 parked keeper pad, 3/4 ply

have it
TBD

D2 travel latches, closed and parked

printed
  • Order: post and infill into the hole (dry structure); the cab wall's wedi and microcement, wrapped round the hole's top edge; then the bracket bolted through above the hole (washers and nylocks on the cab side), the track into the bracket, the door hung. The track is not ordered yet, so the bolt holes wait for it.
  • The bracket: the Husky track is made to screw up into a ceiling. On a wall it needs something to hang from: a bent stainless angle (cut and bent at SendCutSend), or Husky's own face-fix bracket if Woodward's has one. Ask them first.
  • Water: the door's wet face lines up with the cable box's face; the sweep brushes the box top; the jamb seal closes the wardrobe edge. The track and bracket sit above the spray line, every screw hole sealed.
  • Sizes: door 20 11/16 x 36, opening 19 3/4 wide, travel 20 11/16. Renders: the shower, rendered.
Tap a part, or a row on the left.