The bed boards, cut by cut
Shop drawings for the boards, the back slot and the headboard: every notch, groove, hole and wire rail, measured from one end. Rout the LED grooves full length first, then cut the notches; drill the wire holes last, from the groove side.
Head board · Foot board · Inner back wall · Back 1x5 · The slot · Headboard
warm LED grooveRGB LED groovewire rail and lead groovepocketcircles: 3/16 wire holes
Head board, driver side 1x10 ripped to 8 1/2, 60 3/4 x 8 1/2
| cut | along, from the back end | height | size and note |
|---|---|---|---|
| Top notch | 0 to 2 | down 2 1/4 (top at 6 1/4) | 2 long; 1 in radius in the inside corner |
| Top notch | 58 3/4 to 60 3/4 | down 2 1/4 (top at 6 1/4) | 2 long; 1 in radius in the inside corner |
| Strut notch, underneath | 0 to 3 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 19 1/2 to 22 1/2 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 39 3/8 to 42 3/8 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 57 3/4 to 60 3/4 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| LED groove, one for both channels | 0 to 60 3/4 | 2 5/32 to 3 15/32 up from the bottom | 1 11/32 wide, 5/16 deep, outside face: warm channel on top, RGB under it |
| Wire hole, warm | at 1/2 | 5 3/8 below the top | 3/16 through, from the groove bottom to the inside face |
| Wire hole, RGB | at 1/2 | 6 below the top | 3/16 through, from the groove bottom to the inside face |
| Pocket, inside face | 1/8 to 7/8 | 5 1/8 to 6 1/4 below the top | 1/4 deep, chiselled: joins both holes |
| Lead groove, inside face | at 1/2 | down to the slot floor (this end of the head board closes the slot) | 1/4 x 1/4, vertical: leads down to the corner feed hole |
Foot board, passenger side 1x5, 60 3/4 x 4 1/2
| cut | along, from the back end | height | size and note |
|---|---|---|---|
| Top notch | 0 to 7 3/4 | down 3/8 (top at 4 1/8) | 7 3/4 long; 1 in radius in the inside corner |
| Strut notch, underneath | 0 to 3 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 19 1/2 to 22 1/2 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 39 3/8 to 42 3/8 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| Strut notch, underneath | 57 3/4 to 60 3/4 | up 1 1/2 | 3 long, for a 3 x 1 1/2 strut |
| LED groove, one for both channels | 0 to 60 3/4 | 2 5/32 to 3 15/32 up from the bottom | 1 11/32 wide, 5/16 deep, outside face: warm channel on top, RGB under it |
| Wire hole, warm | at 1/2 | 1 3/8 below the top | 3/16 through, from the groove bottom to the inside face |
| Wire hole, RGB | at 1/2 | 2 below the top | 3/16 through, from the groove bottom to the inside face |
| Pocket, inside face | 1/8 to 7/8 | 1 1/8 to 2 1/4 below the top | 1/4 deep, chiselled: joins both holes to the wire rail |
| Wire rail, inside face | 0 to 1/2 | centre 1 1/4 below the top (3 1/4 up) | 1/4 wide, 1/4 deep: the leads ride it to the corner |
Back 1x5 (outer): the back LED board 1x5, 78 3/8 x 4 1/2
| cut | along, from the driver end | height | size and note |
|---|---|---|---|
| Top notch | 67 3/8 to 78 3/8 | down 3/8 (top at 4 1/8) | 11 long; 1 in radius in the inside corner |
| LED groove, one for both channels | 0 to 78 3/8 | 2 5/32 to 3 15/32 up from the bottom | 1 11/32 wide, 5/16 deep, outside face: warm channel on top, RGB under it |
| Wire hole, warm | at 1 1/4 | 1 3/8 below the top | 3/16 through, from the groove bottom to the inside face |
| Wire hole, RGB | at 1 1/4 | 2 below the top | 3/16 through, from the groove bottom to the inside face |
| Pocket, inside face | 7/8 to 1 5/8 | 1 1/8 to 2 1/4 below the top | 1/4 deep, chiselled: joins both holes |
| Lead groove, inside face | at 1 1/4 | down to the slot floor | 1/4 x 1/4, vertical: leads down to the corner feed hole |
| Floor angle | at 12 | on the slot face, on the strut top | small black angle: #8 x 5/8 into the board, #10 self-drilling into the strut |
| Floor angle | at 39 3/16 | on the slot face, on the strut top | small black angle: #8 x 5/8 into the board, #10 self-drilling into the strut |
| Floor angle | at 60 | on the slot face, on the strut top | small black angle: #8 x 5/8 into the board, #10 self-drilling into the strut |
Inner back wall 1x5 ripped to 3 1/2, 76 7/8 x 3 1/2
| cut | along, from the driver end | height | size and note |
|---|---|---|---|
| Top notch | 68 5/8 to 76 7/8 | down 1 3/8 (top at 2 1/8) | 8 1/4 long; 1 in radius in the inside corner |
| Crossing hole | at 1/2 | 2 5/8 below the top (7/8 up) | 3/8 through: the head and back LED leads come across the slot floor and through here |
| Wire rail, inside face | 0 to 76 7/8 | centre 2 below the top (1 1/2 up) | 1/4 wide, 1/4 deep: the leads ride it to the corner, under the motor notch |
| Lead groove, inside face | at 1/2 | from the rail down to the deck, past the crossing hole | 1/4 x 1/4, vertical: leads down to the corner feed hole |
The slot 1 1/4 wide, 2 1/2 deep
Cut through the back edge, bed down. Phone, Kindle, mask. At full up the drive shaft passes over it, so nothing in it taller than about 3 9/16 in. Its floor is the spacer strip behind the back deck panel, level with the deck.
The headboard 55 3/4 x 13 1/2 x 1/2
Stands on the head board, hinged on its inboard top edge, so it can only fold forward onto the mattress. Fold it before the bed goes up.