TopeLeave about Dec 1

Systems / Living / The bed

The bed

The bed on the Happijac lift: frame, headboard, LEDs, pucks, the drag chain.

3 TBD · 20 ready to order · 2 ordered · 15 have it · also: Board shop drawingsBed manual (first build)Routing the channels

Frame, back slot, headboard and lights, on the bed's own model.

The idea

The whole bed in one plan, frame to lights. Frame: four aluminium struts bolted flat across the Happijac rails, a 1/2 in ply deck, and poplar boards standing on the rails round the mattress: a tall head board on the driver side, 1x5s at the foot and back, white oak across the front. Back slot: two 1x5s at the back with a 1 1/4 in slot between them for a phone and a Kindle. Headboard: 14 in above the mattress on the head board, hinged to fold flat onto the mattress before the bed goes up.

Lights: flush channels in two grooves round the outside of the boards (warm and RGB, 33 ft), wire rails and holes carrying the leads to the driver back corner, four slim pucks under the deck for the office, and a drag chain in the rear driver corner behind the back column that follows the bed, then down the corner, along the floor and up to the control box in the aft kitchen upper. In the 3D: Fold the headboard, and Raise the bed (which folds it first).

Five positions from the taped heights

Floor to ceiling 75 1/2, 75 under the slats, which is the number that counts. The bed is 8 from its bottom to the mattress top; the upright headboard as drawn (to be fitted later) stands 14 over the mattress, 22 above the bed bottom; folded, frame and headboard stay within 9. Green: room for a sleeper (20 over the mattress, ASSUMED) or a seated adult (34 over the bench seat, ASSUMED). Brown: not enough. In each drawing the measure above the bed is the room over the mattress, the one below it the floor to the bed, and the one on the right the room over the bench seat. Positions 1 to 3 are taped; 4, split, is Jeff's 57 1/2; 5 shares the space evenly with the lounge bed.

1 Down4324bed at 24, headboard upright2 Cushions274015 1/2bed at 40, headboard upright3 Up1 1/265 1/241bed at 65 1/2, headboard folded4 Split9 1/257 1/233bed at 57 1/2, headboard folded5 Dual bed21 1/421 1/4bed at 45 3/4, headboard upright
positionbed bottommattress topover the mattressunder the bedheadboard
1 All the way down243243under the seat heightupright
2 Top of the lounge cushions40482715 1/2 over the seatupright
3 Up, at the top stop65 1/273 1/21 1/241 over the seatfolded
4 Split (office + sleep)57 1/265 1/29 1/233 over the seatfolded
5 Dual bed45 3/453 3/421 1/421 1/4 to the lounge bedupright
  1. Stop 3/4 short of full up. Fully up (bed bottom 66 1/4) the folded headboard, lying across the 8 1/2 head board, would reach 75 1/4, past the slats at 75. At 65 1/2 it is 1/2 under them. Set the lift's upper limit there, or mark it on a column. The 1/2 the head board stands above the mattress is what lets the headboard fold flat over a crowned mattress.
  2. Split: the headboard cannot stand up. At 57 1/2 the mattress top is at 65 1/2, 9 1/2 under the slats. The upright headboard would reach 79 1/2, 4 1/2 into the ceiling. For it to stand here it could show at most 9 over the mattress, against 14 as drawn; otherwise it stays folded (or lifts off) in split mode, and the sleeper has 9 over it: on your back, not on your side. Underneath, 33 over the bench seat is a little under the 34 assumed for a seated adult.
  3. Dual bed lands at 45 3/4, 5 3/4 above position 2: each sleeper gets about 21 1/4, if the lounge bed is at seat height.

The notches

Each board's top drops at its ends to clear the lift: the spools at the front, the drive shaft at the driver back corner, the motor at the passenger back corner. One groove, warm channel (gold) over RGB (violet) side by side, runs at ONE height round the frame, 2 5/32 to 3 15/32 up from the bottom of every board, so with the bed up it draws the outline of the lounge ceiling. It is centred between the strut notches underneath (1 1/2) and the 3/8 motor notches on the foot and the back 1x5 (4 1/8), with about 5/8 of wood each side, so both channels run every board's full length. Rout full length, then cut the notches.

Head board (driver side), outside face, 8 1/2 tallnotch 2 long, down 2 1/4notch 2 long, down 2 1/4channels 0 to 60 3/4 from its back endBack 1x5 (outer), outside face, 4 1/2 tallnotch 11 long, down 3/8channels 0 to 78 3/8 from its driver endFoot board (passenger side), outside face, 4 1/2 tallnotch 7 3/4 long, down 3/8channels 0 to 60 3/4 from its back end

The shop drawings have each board cut by cut (both faces, a section, a table of every notch, groove, hole and wire rail from one end), plus the back 1x5, the slot and the headboard.

The back slot

Cut through the back edge. The outer 1x5 stands on the rails and carries the back LEDs, facing the rear wall; the inner wall stands on the deck 1 1/4 in in front of it, 1 in taller. A spacer strip on the back strut, level with the deck, is the slot's floor; the head and foot boards close its ends.

rear wallmattressinner wall, 1x5 ripped to 3 1/2, on the deckLED grooves on the outer 1x5, facing the rear wallwire rail, 1 1/2 up the walldeck, 1/2 plyspacer, 1 1/8back strut, 1 1/2 x 3, flatHappijac railTHE SLOT: 1 1/4 wide, 2 1/2 deep, felt floorsmall angle, through the spacer into the strut1 1/4back 1x54 1/2

Wiring bed to the control box

Everything on the bed meets in the junction box at the driver end of the back slot, rides one cable down the drag chain and along the floor to the control box in the aft kitchen upper, and the box takes one fused feed from the 12 V bus. Eight channels: warm, red, green, blue, pucks white, pucks red, fan 1, fan 2. The fans are two Caframo Sirocco IIs, one under each front corner angled in, folding flat between the struts; channels 7 and 8 only switch them on and off, their own buttons set the speed.

ON THE BEDJUNCTION BOXCABLE, 12-CORE 18 AWG, ABOUT 27 FTCONTROL BOX12 V BUSin the back slot,driver enddrag chain, then along the flooraft kitchen upperWago 221sQuinLED+12 V+ out+12 V+ out+12 V+ outwarm -ch 1 warmred -ch 2 redgreen -ch 3 greenblue -ch 4 bluepucks white -ch 5 pucks whitepucks red -ch 6 pucks redfan 1 -ch 7 fan 1fan 2 -ch 8 fan 2sparecappedWarm striptop channel, head, back and foot2-core: + and warmRGB striplower channel, head, back and foot4-core: +, R, G, B4 pucks, whiteunder the deck, the office lights3 wires each: + shared4 pucks, redthe same pucks, night lightthe third wireFan 1, Siroccounder the deck, driver frontpair, in its deck grooveFan 2, Siroccounder the deck, passenger frontpair, in its deck grooveswitch+ 15 A fuse(at the bus)- load sideof the shunt14/2 tinnedduplexWiZmoteremote, loungeESP-NOW+12 V, sharedreturn (switched by the controller)wirelessEvery channel switches its load's negative; + is common. The cores between the boxes carry one return per channel.

The junction box

Inside it is only Wagos. Each one ties a few wires together. Two kinds: joins, where several wires from the bed become one (all the + wires; the four pucks' whites; their reds), and straight through, where one wire from the bed just carries on as one core of the cable (warm, R, G, B, each fan's -). Nothing changes inside: it is all extension and joining.

COMES IN, FROM THE BEDTHE WAGOGOES OUT, ON THE CABLEJOINS: many + wires become oneEvery + on the bed ties together here and leaves on three cores side by side (more copper, less voltagelost). The pucks' four + wires join first, then one jumper carries them in.Pucks +1 x 221-415Puck 1+ wirePuck 2+ wirePuck 3+ wirePuck 4+ wirejumper into the +12 V bus+12 V bus3 x 221-415Warm strip+ wireRGB strip+ wireFan 1, driver front+ wire (red)Fan 2, passenger front+ wire (red)Pucks + Wagojumpercore 1to the controller's + outcore 2to the controller's + outcore 3to the controller's + outSTRAIGHT THROUGH: one wire, one coreNothing joins. The Wago just extends the bed's wire onto its own core in the cable, so the controller can dimit alone.Warm1 x 221-412Warm stripwarm wirecore 4to channel 1, warmRed1 x 221-412RGB stripred wirecore 5to channel 2, redGreen1 x 221-412RGB stripgreen wirecore 6to channel 3, greenBlue1 x 221-412RGB stripblue wirecore 7to channel 4, blueFan 11 x 221-412Fan 1, driver front- wire (black)core 10to channel 7, fan 1Fan 21 x 221-412Fan 2, passenger front- wire (black)core 11to channel 8, fan 2JOINS: four pucks become one channelAll four pucks' white wires tie together and share one core, so the four dim together. The same for the redwires.Pucks white1 x 221-415Puck 1white wirePuck 2white wirePuck 3white wirePuck 4white wirecore 8to channel 5, pucks whitePucks red1 x 221-415Puck 1red wirePuck 2red wirePuck 3red wirePuck 4red wirecore 9to channel 6, pucks redSPARECore 12 lands in a Wago on its own, capped and labelled, for whatever comes later.Spare, capped1 x 221-412nothing from the bedcore 12capped at both endsA Wago ties together every wire in it: any port, same connection. Hover or tap a row to see what it does.

Where it sits, from above. The slot is 1 1/4 wide and 2 1/2 deep; the box takes the first 9 in at the driver end and the phone and Kindle get the rest.

DAABdeck grooves: pucks and fansdriver wallrear wallJUNCTION BOXchain
  • Port A: the slot's driver end. The strips' leads, through their 3/16 holes in the head board and the back 1x5.
  • Port B: under the inner wall. The deck grooves carry the puck and fan wires back and through a 3/8 notch in the wall's bottom edge.
  • Port C: through the inner wall, from the wire rail. Only if you add the far-end feed: a second warm and RGB lead from the passenger end.
  • Port D: out through a 1/2 hole in the head board at the slot's end, above the LED channel, straight into the drag chain.
Wagotypebed sidecores out
+12 V bus3 x 221-415warm +, RGB +, fan 1 +, fan 2 +, pucks + (jumper)1, 2, 3
Pucks +1 x 221-415puck 1 +, puck 2 +, puck 3 +, puck 4 +(jumper to the bus)
Warm1 x 221-412warm4
Red1 x 221-412R5
Green1 x 221-412G6
Blue1 x 221-412B7
Pucks white1 x 221-415puck 1 W, puck 2 W, puck 3 W, puck 4 W8
Pucks red1 x 221-415puck 1 R, puck 2 R, puck 3 R, puck 4 R9
Fan 11 x 221-412fan 1 -10
Fan 21 x 221-412fan 2 -11
Spare, capped1 x 221-412nothing: the core is capped12

Buy: 6 x Wago 221-415 (5-port), 7 x 221-412 (2-port), and 4 x 221-413 (3-port) for the far-end feed or spares: a mixed Wago 221 pack covers it. Two 2 in jumpers of 18 AWG link the three bus Wagos. Labels on every wire at both ends: W, R, G, B, PK-W, PK-R, FAN1, FAN2, +.

The box: printed PETG, 9 x 1 1/8 x 2 1/4 outside, lid on top held by two screws. Inside, the Wagos stand on edge in two lanes along the slot, their wires entering end-on. A zip-tie post at each port: tie every bundle before it reaches a Wago, about 6 in of slack inside. If the slot turns out too tight, the same Wagos fit a 4 x 4 x 1 1/2 box under the deck at the same corner.

The pucks' wires: + is shared; the other two are white and red. Before you join them, touch each pair to 12 V and mark which is which.

The cable's cores

corecarriesat the controller
1+12 V+ out
2+12 V+ out
3+12 V+ out
4warm returnchannel 1
5red returnchannel 2
6green returnchannel 3
7blue returnchannel 4
8pucks white returnchannel 5
9pucks red returnchannel 6
10fan 1 returnchannel 7
11fan 2 returnchannel 8
12sparecapped, labelled

Eleven cores used, one spare. Continuous-flex, drag-chain rated, 18 AWG.

In the control box

whathow
Cable inThrough a grommet, strain relief (a zip tie to a printed post). Every core labelled at both ends.
+12 V coresThe three +12 cores on one Wago 221-413, then one lead to the controller's + output.
Channel coresWarm, red, green, blue, pucks white, pucks red, fan 1, fan 2 into channels 1 to 8. The spare core coiled and capped. The other seven channels stay free for other lights in the truck.
ControllerQuinLED A, An-Penta-Deca (ESP32, WLED now, ESPHome later), channels A1 to A8: dims every channel; the WiZmote remote (ESP-NOW) and the phone talk to it. Channels 7 and 8 set to switch fully on, never dimmed: the fans set their own speed.
SwitchA rocker on the box's face in the + feed: everything off without the app.
FeedThe bed is on QuinLED A, which also runs the garage and the outdoor light: its feed is 12/2 tinned duplex from the DC box's Lights A position, 20 A fuse at the DC box end. The whole lighting system: lighting-overview.html.

Cut through

Show

What's in it 40 parts

Frame

have it

Struts, 6061 tube 1 1/2 x 3 x 1/8, lying flat

have it
have it

Strut bolts, 1/4-20 x 3/4

have it
have it

Deck, 1/2 in ply, three sheets

have it
have it

Head board, poplar 1x10 ripped to 8 1/2

have it
have it

Foot board, poplar 1x5

have it
have it

Front, 1x6 white oak ripped to 4 1/2

have it
have it

Black corner braces, 1 1/2 and 2 in, #8 wood screws

have it
ready to order

Shellac primer and a grey satin enamel

stock
ready to order

Rubio Monocoat Oil Plus 2C, Pure

stock

Back slot

have it

Back 1x5, the outer edge of the slot

have it
have it

Inner back wall, poplar 1x5 ripped to 3 1/2

have it
have it

Spacer strip, 1/2 in ply or poplar

stock
TBD

Small black angles, about 1 x 1

stock
ready to order

Felt or cork strip for the slot floor

stock

Headboard

ready to order

Headboard panel, 1/2 in ply

stock
have it

White oak veneer for the headboard, both faces, and contact cement

have it
have it

Matte black hinges, 1 1/16 x 12 in

have it
ready to order

Locking lid supports, matte black

stock
TBD

Travel hold for the folded headboard (to decide)

stock

LED rails

have it

Aluminium U channel, 16.93 mm wide, black, frosted diffuser, end caps

stock
have it

Warm strip, BTF FCOB 2700K 528/m, 12 V

have it
ready to order

RGB strip, BTF FCOB 810/m, 12 V, 4-wire

stock
ordered

Strip-to-wire clips, 10 mm 2-pin COB (warm strip)

stock
ready to order

Strip-to-wire clips, 10 mm 4-pin RGB COB, with 10 ft 22 AWG 4-core

stock
ready to order

LED grooves, routed (if not already)

cut from stock

Wire rails

ready to order

Wire rails: 1/4 x 1/4 groove and the wire holes

cut from stock
ready to order

Strip leads: 22 AWG, 2-core and 4-core

stock
ready to order

Aluminium foil tape

stock

Pucks and fans

have it

Caframo Sirocco II 12 V gimbal fans, x2

have it
ready to order

Slim 12 V surface pucks, 2700 to 3000K, 3/8 or thinner

stock
ready to order

Puck holes and deck grooves

cut from stock

Side run and control

ready to order

Junction box in the slot, printed, with Wago 221 lever nuts

stock
ready to order

Drag chain, 10 x 15 mm inside, about 4 ft

stock
ready to order

Continuous-flex cable, 12-core, 18 AWG, about 27 ft

stock
ready to order

Cable clips and grommets

stock
ordered

QuinLED An-Penta-Deca controller (ESP32)

stock
ready to order

Lights A fuse (20 A, at the DC box) and master rocker A

stock
ready to order

12/2 tinned duplex, DC box to the control box (Lights A)

stock
ready to order

Wireless remote for the bed, WiZmote (ESP-NOW)

stock
TBD

Control box, printed cover

printed
Tap a part, or a row on the left.