Floor plan
The box interior as the build documents actually describe it, drawn to scale. Tap anything for what it is, its numbers, how each number is known, and which page it came from. Solid lines are taped, specified, derived or decided. Dashed lines are read off a photo or inferred, and those are the ones to check before cutting anything.
On a phone the plan scrolls sideways. Layers and the bed toggle sit above it.
How the length adds up
Everything along the van is placed by one chain from the cab wall. Two links rest on an inference rather than a tape: the column's fore-and-aft size, and that the fridge bench starts right behind the column. The garage is whatever is left, so if any link is wrong, the garage is where it shows.
This also answers the old question of the 10 unallocated inches in layout.html: the galley wall is 56 because the window panel is 56 and runs pillar to bath door, not 50, and the garage comes out about 27, not 24.
| link | in | how known | |
|---|---|---|---|
| Bath, cab wall to wardrobe front | 22 3/16 | measured | 2026-08-23 |
| Partition plywood | 1/2 | measured | dry-fit panel |
| Galley wall, partition to pillar | 56 | derived | the 56 in window panel spans it |
| Happijac column | 2 1/2 | assumed | B21 on the measure sheet |
| Fridge drawer face | 5/8 | measured | 2026-09-09 |
| Passenger bench run | 59 | measured | 2026-09-09 |
| Garage, the remainder | 27 3/16 | derived | carries every error above |
| Box interior length | 168 | spec | Unicell |
What this drawing does not know yet
Every dashed element, weakest first. Tap a row to find it on the plan. The codes are the rows on the measure sheet.
| element | how known | tape |
|---|---|---|
| Buyers underbody box | photo | not on the sheet |
| Entry door | photo | B7, B8, E1 |
| Lounge window, driver side | photo | E6 |
| Lounge window, passenger side | photo | E6 |
| Rear barn doors | photo | E3 |
| Sink | photo | not on the sheet |
| Bed platform | assumed | C8, H1, H2, D4, D5 |
| Bed underside pucks | assumed | not on the sheet |
| Ceiling pucks, main | assumed | not on the sheet |
| Chassis frame rail, passenger | assumed | not on the sheet |
| Chest fridge slide travel | assumed | B13, B14 |
| Control box | assumed | not on the sheet |
| Core pocket: Isotemp and pump | assumed | not on the sheet |
| Fresh tank | assumed | C7 |
| Galley counter | assumed | B9, B10, C3, D1 |
| Grey tank, to buy | assumed | not on the sheet |
| Happijac columns, forward | assumed | B21, C8, H1, H4 |
| Kitchen window | assumed | E5, D9 |
| Shower drain, candidate | assumed | not on the sheet |
| Task pucks | assumed | not on the sheet |
| Undermount utility box | assumed | not on the sheet |
| Upper cabinets | assumed | B11, B12, C4, D2 |
Conflicts
Places where the plan, drawn from the documents, disagrees with itself or where two documents disagree with each other. Each is a question for the tape, not a decision.
- Fridge slides against the forward Happijac column. The chest fridge rides out forward past the passenger-side column. On the numbers drawn, a 19 in fridge centred in the 22 5/8 bench and a column standing 2 1/2 off the wall, the two overlap by about 1/8 in. Both numbers are unmeasured. Tape B14 (fridge fully out) and C8 (column faces) before trusting the slides.
- Isotemp orientation in the bay. The July note has the heater on edge against the passenger wall, long axis fore and aft. The 2026-09-09 correction has it along a crossways bulkhead and describes the pocket as bulkhead to tank face. Both agree on the pocket size and the 9 3/4 gable clearance; they do not agree on which way it faces.
- RO position. dimensions.json puts the RO 54 1/2 to 72 in aft; the photos put the sink, which the RO sits under, in the forward half of the counter.
- Which NRX fridge. context.md says NRX50E, the measure sheet says NRX 35E.
- Galley length and garage depth. layout.html has 50 and 24. The window panel makes the galley wall 56, and the chain then leaves 27 3/16 for the garage.
- Lounge width against the Happijac track. The lounge is taped 80 1/2 across. The bed page derives the finished width as 81 5/8 and assumes the track stands 2 1/2 off the shell. Which surface the 80 1/2 was taken to is not recorded, and it moves the platform width. C8 settles it.
- Underbody boxes. The shower notes put an undermount utility box under the shower, taking the first 16 in from the driver wall. The water notes say S10, the undermount box, is the Buyers box Jeff already owns, below the water bay. The exterior photo shows a box under the entry door as well. How many boxes there are, and which is which, is not written down.
Not drawn, on purpose
These are in the build, but no document says where they go, so they are listed rather than given an invented spot.
- Dometic NRX compressor fridge. context.md says NRX50E, the measure sheet says NRX 35E, and no document says where it goes. B15 on the measure sheet.
- Eberspacher diesel heater. Planned 'under a bench seat', model still open (D2, D4, D5, Hydronic). Which bench is not recorded.
- Cruise N Comfort A/C. Installed, about 45 A DC. The old layout elevation drew it high in the garage, driver side; nothing newer confirms it.
- Inverter, Lynx, WFCO panel. Garage lower level with the batteries, per layout.html. No positions.
- Ceiling escape hatch. Over the front area. Size and position not measured.
- 14 in roof fan. Cutout written on the joist; 'near the bed boundary' in photos, not taped.
- Indoor shower fan and porthole. VETUS FAN12 and PW201P, reserved on the cab wall, purchase and cut deferred.
- Happijac aft columns. The lift has a pair at each end of the bed. Only the forward pair is placed by any document; the aft pair's station and how the benches clear it are not recorded. B21 and C8.
- Floor holes H-1 to H-8. A 6 x 12 in patch in the water bay, centre to passenger side. Where the patch sits in the bay is not taped, so it is on the floor holes page rather than drawn here.
Where the facts came from
Bath and cab opening: the shower construction record, taped 2026-08-23 and 24. Benches:
Jeff's lounge tape, 2026-09-09. Galley wall: the kitchen window panel cut sheet, 2026-08-07,
with the walls plan for what it butts. Water bay: the water system entry and its 2026-09-09
re-measure. Bed: the bed platform page. Entry door and lounge windows: the 2026-07-12 exterior
photo. Chassis: Ford's body application figures. The numbers live in
model/dimensions.json and in the lounge and bed generators, and this page reads
them from there. The photo estimates and the assumptions are set in the floor plan generator
itself, and every one of them is drawn dashed.