TopeLeave about Dec 1
← Installing the Isotemp

Isotemp install manual

Interactive9 phases, 26 steps

The kit's install guide as a checklist, in order, done Tope's way. The diagram follows you: as you scroll, it builds the system up to the step you are on, and Play runs the whole install. Tick each step as you finish it; ticks stay in this browser. Copper boxes are where Tope does it differently from the guide.

Steps follow Vanlife Outfitters' guide, Revision 11. The page links under each step open Jeff's photo of that page of the guide. Where the guide and Isotemp's own manual disagree, the manual wins.

1Before you start

Nothing gets cut in this phase.

    1. Read Isotemp's own manual for the Slim Square before this one. Where they disagree, Isotemp wins: it is their heater.
    2. Study the parts diagram until you can trace coolant out of the engine, through the heater and back.
    Caution Eye protection, gloves and ear protection throughout. Coolant is toxic and the dog will drink it: clean every spill.
    Guide pages p1 p3 p4 · full text
    1. Standard kit: 2 brass 5/8 barb x 1/2 FNPT fittings, 2 PVC reducer bushings 1-1/4 x 3/4, 50 ft Gates 28411 5/8 heater hose, 2 brass reducing tees 3/4 x 3/4 x 5/8, 2 brass 5/8 90 degree elbows, 2 5/8 brass ball valves, hose clamps (stainless or Gates PowerGrip), thread sealant, red high-temp RTV, 20 insulated P-clamps, 20 #8 self-tappers, 10 stainless zip ties, 6 ft foam insulation.
    2. Ford Transit kit adds: 1 ft of 3/4 heater hose, 2 more 5/8 elbows, 4 more clamps. You need these for the loop in Phase 2.
    Guide pages p2 · full text
    1. Hose cutter, heat gun (for PowerGrip clamps), two adjustable wrenches, small bucket and towels, 1/8 drill bit, the hole saw for the coolant holes, round file, funnel, drill.
    2. Hose pinch-off clamps: they cut the spill when you cut the hoses and speed up bleeding.
    3. Coolant to top up.
    Tope The guide says Mopar coolant, which is for a Ram Promaster. A Transit takes Ford's: Motorcraft Yellow, WSS-M97B57-A2, mixed with DISTILLED water. Check the reservoir cap before buying, and never mix coolant types.
    Tope Hole saw: 1 3/8, not the guide's 1 3/4. See Phase 4.
    Guide pages p2 p3 · full text

2Place the heater

No plumbing or wiring yet.

    1. Seat the unit where it will live and strap it down on its brackets with real fasteners into the 8020.
    2. The safety valve and its drain must be the lowest point of the unit.
    Tope The guide recommends lying flat. Tope's bay gives 18 1/2 in clear and the unit is 23 1/4 long, so it lies on its edge. That is allowed as long as the safety valve stays lowest.
    Tip Leave the connection face reachable. The manual wants a foot in front for service; the pocket gives about 9 3/4, which is why the connections go on unions.
    Guide pages p4 p5 p6 · full text
    1. Take the front cover off and find the green thermal cut-off with its tiny red reset button.
    2. Cut a small hole in the cover over it so a pencil eraser can press the reset with the cover on.
    Tip It trips, particularly when switching from coolant heat to electric. Two builds say so independently. If the element ever stops heating, press this first.
    Guide pages p6 · full text

3Tap the engine coolant

Engine cold: do this after the truck has sat overnight.

    1. Work on a cold engine only.
    2. If it helps, unbolt the coolant reservoir and lay it aside without disconnecting it.
    Caution Never open a hot cooling system.
    Guide pages p6 · full text
    1. Find the two heater hoses where they go through the firewall.
    2. Pinch-clamp each a few inches back, towel underneath, then make one clean, square cut in each.
    Tope On a Transit, the heater core connects to a rigid pipe through a short molded hose with very little room between them. See the next step before you cut.
    Guide pages p7 p8 p10 · full text
    1. Push a short piece of the 3/4 hose onto the heater core, and onto one 3/4 side of a reducing tee.
    2. Outside the engine bay, join two 12 to 18 in pieces of 5/8 hose with the two extra brass elbows.
    3. Use that assembled piece to bridge from the tee's other side to the rigid pipe. The 5/8 hose onto the tee's 3/4 barb is a tight fit, and it does go.
    Tope This loop is the Ford Transit part of the kit. Promaster and Sprinter vans skip it.
    Guide pages p10 p11 p12 · full text
    1. A clamp on each side of each cut, then push the tee's 3/4 barbs into the hose ends. Do the supply hose first.
    2. Secure every joint: stainless clamps, or Gates PowerGrip shrunk with the heat gun kept moving about 2 in off, all the way round.
    Tip Two tees means PARALLEL: the cab heater and the water heater share the pump. That is what this kit is built for.
    Guide pages p8 p9 · full text
    1. From each tee's 5/8 side: a short length of 5/8 hose, then a 5/8 ball valve, clamped at every joint.
    2. Label the valves SUPPLY and RETURN with a marker.
    3. Leave the valves CLOSED.
    Guide pages p9 · full text

4Run the lines

Two 5/8 hoses from the valves to the heater.

    1. Tape-label the end SUPPLY.
    2. Feed it down the back of the engine bay, through the gap on the driver side toward the ground. A helper above and you underneath makes this much easier.
    3. Route it back along the frame to the heater's location.
    Caution These hoses get extremely hot. Keep them off anything heat can damage, and away from the exhaust.
    Guide pages p12 p13 · full text
    1. Cushioned P-clamps and #8 self-tappers into structure, not into anything that might be a pipe or wire. Zip ties where a clamp will not go.
    2. Foam or heat-rated sleeve wherever the hose passes a sharp edge.
    Guide pages p13 p14 · full text

5Holes through the floor

Only the two coolant holes here; H-1 is the drain.

    1. From inside, mark both centres close to the heater, so the least hose is inside the van.
    2. Check below for obstructions, drill 1/8 pilots, then go underneath and confirm both.
    Tope These are H-2 and H-3 on the floor holes page, with positions already planned around the crossmember.
    Guide pages p14 p15 · full text
    1. Cut from inside with the hole saw, guided by the pilots.
    2. Bed a sleeve in each hole, sealed at the TOP only so any weep drains out underneath where you can see it.
    Tope The guide cuts 1 3/4 and glues in the kit's PVC reducer bushings with red RTV. Tope cuts 1 3/8 and sleeves each hole with a 1 in galvanised steel nipple, because this hose runs near 190 F through a 2 1/4 in floor with foam inside. Keep the PVC bushings for something else.
    Guide pages p15 · full text
    1. Push the supply hose up through its hole and route it to the heater. Leave 6 to 8 in spare, then cut it to length at the valve end. Do not connect it yet.
    2. Repeat for the return hose beside it.
    3. Seal round both hoses at the top of the sleeves with high-temp RTV.
    Guide pages p15 p16 · full text

6Connect at the heater

The coolant side, at the unit.

    1. Remove the white plastic caps from the two ENGINE ports.
    2. Thread sealant on the heater's male threads, then fit the two 5/8 barb x 1/2 FNPT fittings, holding the port with a second wrench.
    3. Wait 24 hours before any coolant or water goes through.
    Tope Three sealants are named in the box: Permatex 59214, Loctite 592 and Loctite PST 592. Isotemp's manual says Loctite 577 or Bondline T777. Use the heater maker's.
    Guide pages p17 · full text
    1. Clamp one hose to each engine port. It does not matter which is which: coolant just loops through.
    2. Use the 5/8 elbows wherever a hose would otherwise kink.
    3. Wrap the hose inside the van in the foam insulation.
    Guide pages p17 p18 · full text

7Fill, test and bleed

Have a helper at the key and towels ready.

    1. Funnel coolant into the open supply hose at the engine bay until nearly full, leaving the last 10 to 15 in empty. Clamp or pinch it, then connect it to the supply valve.
    2. Same for the return hose and valve.
    3. Valves still CLOSED. Reservoir back in place.
    Guide pages p18 p19 · full text
    1. Start the engine and idle. Check every joint at the tees.
    2. Leak: engine off, clean up, tighten or re-shrink, test again.
    Guide pages p19 · full text
    1. Engine idling: open one valve slowly, then the other.
    2. Check the valves, then every fitting inside the van, including at the heater.
    3. Helper watches the reservoir. If it drops below LOW, engine off, let it cool, top up.
    Tip Pinch the cab heater loop shut briefly and all the pump's flow goes round the new loop, which fills it faster. When the hoses near the heater warm up, remove the pinch clamps.
    Guide pages p19 · full text
    1. Bubbling in the reservoir is air leaving the system, and it is normal.
    2. Bleed any air until only liquid comes out, then close it.
    Note The guide's bleeder valve is on a Promaster. Find the Transit's bleed point in Ford's procedure.
    Guide pages p19 p20 · full text
    1. Drive a mile or two under 35 mph. Back home, both heater hoses should be hot to the touch.
    2. Recheck the reservoir and bleed once more at idle.
    3. Re-torque the worm clamps after the first few heat cycles.
    Guide pages p20 · full text

8Potable side

Fresh water in and out.

    1. Cold in is 1/2 NPT outside thread. Warm out is 1/2 BSP: use a gasketed swivel there, never a tapered NPT female.
    2. Hold the heater's compression fitting with a second wrench whenever you tighten. It damages or loosens easily.
    Guide pages p17 p21 · full text
    1. Put a ball valve on the cold line before the heater, for service and winterising. One after the warm outlet is worth having too.
    2. Set the outlet temperature with the built-in mixing valve beside the warm outlet.
    Tope Before the heater sees water: the Slim Square's manual caps the pump at 42 psi, and the Shurflo shuts off at 55. Measure the real cut-out and turn it down, or fit a regulator.
    Guide pages p21 · full text
    1. Run the safety valve drain to a free outlet below the unit with no valve and no cap.
    2. It weeps as the water heats. That is it working.
    Tope Tope's is H-1, already cut: a short PEX stub through a PVC sleeve, open, and tagged so nobody stops the drip.
    Guide pages p16 · full text

9Electric element

750 W at 120 V.

    1. Plug the heater into a switched, GFCI-protected 120 V outlet near the bay, with an LED so you can see when it is on.
    2. Use it on shore power or strong solar; through the inverter it is a heavy load.
    Caution Never switch the element on until the tank is full of water. Dry-firing kills it.
    Guide pages p22 · full text