TopeLeave about Dec 1

Systems / Water / Shower / Kitchen door in 3D

Shower

wedi floor and walls, the swing door to the kitchen, the slider to the cab, microcement.

D1, every part, open and shut.

The kitchen door

D1 on its own, from the plan's numbers. Its kitchen face is flush with the frame, just a 1/8 dark gap round it. The catch is on the door: a lip on its shower face drops into a notch in the frame and squeezes the gasket there.

Pull apart spreads every part out with its name. Open doors swings it into the shower. Play the build puts it together in order. Tap any part for what it is.

Its parts 15

ordered

wedi Fundo Primo base, 36 x 72, center drain, US9100006

stock
ordered

wedi Lean curb, 60 in, US3000038

stock
ready to order

D1 air slots, routed through the door

cut from stock
ready to order

D1 hinge upright, poplar 1 1/4 x 1 1/2, 72

cut from stock
ready to order

D1 strike jamb, poplar 1 1/4 x 1 1/2, notched

cut from stock
ready to order

D1 head, poplar 1 1/4 x 1 1/2, notched

cut from stock
have it

D1 infill above the head, 1/2 ply

have it
ready to order

D1 apron, poplar 1x4, kitchen side

cut from stock
have it

D1 leaf, 12 mm Baltic birch

have it
ordered

TACO Marine 304 stainless piano hinge, 1 1/2 x 72, 0.037 (H14-0112A72-1)

stock
ready to order

D1 catch lip, 1/4 x 1 poplar on the door's shower face

cut from stock
TBD

D1 latch, worked from both faces, and its keeper

stock
ready to order

D1 corner magnets: cup magnets and steel strikes

stock
ready to order

D1 frame screws and glue

stock
TBD

Door seals, EPDM bulb (D1 and D2)

stock

Where the gasket is

Looking down on the shut door, cut level at the latch (38 in), drawn large: first the hinge side, then the latch side. Hover or tap a number to see what it is.

HINGE SIDEKITCHENSHOWER1234567891011
  1. 1Wardrobe
  2. 2Wardrobe wall: wedi and microcement, stopping at the upright
  3. 3Hinge upright, poplar 1 1/4 x 1 1/2
  4. 4Screws through the upright into the wardrobe's side panel, every 12 in, glued
  5. 5Hinge leaf on the upright's opening face
  6. 6Hinge knuckle: the door pivots here and swings into the shower
  7. 7Hinge leaf on the door's shower face
  8. 8Door, 12 mm Baltic birch, microcement both faces
  9. 9Microcement on the door's shower face
  10. 10Microcement on the door's kitchen face, flush with the frame
  11. 111/8 gap: the kitchen face is flush, dark behind
LATCH SIDEKITCHENSHOWER123456789
  1. 1Latch handle with a thumb lever, kitchen side
  2. 2The lever's link through the door
  3. 3Latch body on the door's shower face
  4. 4Latch bar: reaches over the lip and drops into the keeper
  5. 5THE CATCH: a 1/4 x 1 lip on the door, half past its edge
  6. 6THE GASKET: bulb seal in the notch, squeezed by the lip
  7. 7Strike jamb, notched; screws into the partition's edge
  8. 8Keeper on the jamb's shower face
  9. 9Partition, wedi on its shower side

The two cup magnets are in the lip near the top and bottom, not at this height, with steel strikes in the notch opposite them.

  • How it shuts: the door swings toward the kitchen until the lip on its shower face lands in the frame's notch and squeezes the gasket. The latch bar drops into the keeper and holds it there; the two magnets pull the top and bottom corners in.
  • How it opens: from the kitchen, press the thumb lever on the handle and push. From the shower, lift the latch bar and pull. It never locks you in.
  • Water: spray pushes the lip harder into the gasket; the sweep sends splashes back over the curb; the hinge closes the hinge side.
  • Sizes: door 18 x 67, walk-through 18 1/4, opens 80 degrees. On the photo: kitchen door mockup.
Tap a part, or a row on the left.