Systems / Outside / Slide-out deck
Slide-out deck
Under the door: a fold-out step, or a two-leaf deck from box to box.
Brackets, slides, both leaves, the hinge, the step well, the skirt, the legs. The drawing builds up as you scroll.
Build
Every step in order. Scroll and the drawing follows: it builds up to the step you are on and lights what that step adds.
Settle step 1
Check before buying
- Tape the crossmember bottoms to the ground at the bay, on level ground: the deck top lands 1 3/8 in below them, the half deck 1/4 in below.
- Slides: lock-in and lock-out, about 550 lb a pair, flat enough to fit beside A under the crossmember with the plate in its slot.
- Tape across a passenger box door to the body edge: the bands and the skirt land in that plane. Pick plain black or diamond plate.
Rails steps 2 to 4
Clamp plates and drop brackets
- Clamp plates: slide a 2 x 3 plate into the slot of each crossmember a rail hangs from (B for R1, F for R2, the one at the back box for R3), two per rail, about 2 and 20 in in from the body edge.
- Drop brackets of 2 x 2 x 1/4 angle, two per rail, two 3/8 bolts through each plate: 3 1/8 long for R1 and R2, 4 for R3.
- R2's have a short fore-aft offset arm, because crossmember F is not right over A's aft end. Paint everything black.
Caution Bolt to the body crossmembers only. Nothing into the Ford frame.
Hang the slides
- R1 and R2: fixed members on the inside faces of their brackets, side-on, the moving member toward A.
- R1 and R2 exactly 52 1/2 apart, centre to centre: A and its two end bands. Their tops -1 5/8 below the crossmember bottoms.
- R3 where B's free end lands: a slide pair lying flat, its top 2 1/2 below the crossmember bottoms, so B rests on it level with A.
Level and square
- A straightedge across R1 and R2, then on to R3: all dead level. Shim at the clamp plates, never by bending a bracket.
- Pull all three out: the diagonals across R1 to R2's ends equal within 1/8, or A binds.
Tip Get this right and the rest is easy: a racked rail is the one thing you feel every time.
Leaves steps 5 to 9
Cut both leaves from the sheet
- Two 51 x 22 from the 4 x 8 sheet of 1 1/8 marine ply, side by side. 1/2 in radius corners, 1/8 roundover on every edge.
- Drill every hole now, oversize, fill with epoxy, redrill (the boatbuilder's trick: no bare wood in any hole). Threaded inserts set in epoxy where something bolts on and comes off: A's end bands, hinge, step frame, leg hinges; B's hinge and leg receivers.
- Three coats of epoxy on every face and edge, sanded between. Then the walking surface.
Tip Mark both leaves' insert positions together, A on B as it will fold: the hinge and the face bands then line up.
Leaf A
- A 2 x 1/4 aluminium end band on each 22 in end, flush with the top, bolted into the inserts: the R1 and R2 slides bolt to them.
- The face band on the outer long edge, 1/8 x 1 1/8, black, flush with the top.
- The walking surface on top.
Leaf A onto R1 and R2
- Bolt the slides' moving members to A's end bands, slide it home: the band flush with the box doors, 1/4 in clear of the front box.
- Run it in and out ten times. It should glide and lock both ways.
Leaf B
- Its face band on the outer long edge, flush with the top. The walking surface on BOTH faces: folded on A, its back is the landing.
The hinge
- Lay B face down on A, ends square. Piano hinge across the joint on the top faces, over R2, cut to 21 in.
- Folded, B lies on A with 1/4 in under the crossmembers: the half deck. Open, it flips back over the tire onto R3's pulled-out slide, level with A: the full deck.
Tip Fit the hinge with A and R3 pulled out and B resting on R3.
Steps step 10
The step well and the GlowStep
- Two 1 1/2 aluminium angles bolted up into A's inserts at its outer edge, 5 1/4 to 30 3/4 from the back of the front box (under the door), 25 to 25 1/2 apart inside.
- The GlowStep's factory brackets bolt to them, its opening at A's outer edge, the steps hanging outboard.
- Stored, it collapses and latches in its own frame: about 8 in deep and 14 1/4 in below A's top. Check A slides fully home with it stored.
Caution Buy it first and fit the angles to its brackets: the well's width and the skirt's cut-out follow it.
Skirt step 11
The skirt on A
- One sheet, 51 long by 11 1/2 tall, a 1 in return along its bottom; the step well cut out, 26 wide, full height.
- Two hangers of 1 x 1 angle down from each end band to the skirt's bottom; a return along its top riveted under A's face band. It rides with A.
- Stowed, check: its face in the plane of the box doors, its bottom level with the box bottoms, 1/4 in to the front box.
Tip Stowed, the bay is one black face: two bands over the skirt, the folded steps in their well, box bottoms lined up.
Legs steps 12 to 13
Make the four legs
- Each: outer tube 1 1/4 x 0.058, 18 in; inner 1 1/8 x 0.058, 18 in, 1/4 holes every inch for its lower 10 in; a ball-lock pin through the outer tube; a levelling foot in a threaded plug.
- A's two: a 5/16 cross hole at the outer tube's top for the hinge bolt, a tab 9 in down for the brace. B's two: a 1/4 hole near the top for the socket pin.
Fit the legs
- A's legs: hinges into A's inserts at its two outer corners, 1 1/2 in from each end. Each folds inward, across the leaf, flat under it, clear of the step well; a brace locks it vertical, a spring clip holds it folded.
- B's leg receivers: flush, bonded into B's outer edge underneath, mid-length and 2 in from the free end (flush because folded, that face is the landing).
- Two spring clips under A near its inner edge, along its length: B's legs lie in them, flat, when they are off. They ride in and out with A.
- Pins through each rail for travel.
Tip Half deck for getting in and out: no legs. Hanging out on it, two people, or the full deck: A's legs down, and B's two for the full deck.
Using it step 14
The three states
- HALF DECK, the everyday one: pull the handle, slide A out (B rides folded on it), flip the GlowStep's lever and let it down to the ground. The landing is 4 1/2 below the door, then 7 1/2 in steps.
- FULL DECK: from the half deck, pull R3 out, flip B back over the tire onto it, pin in B's two legs, drop A's two. The same steps, from 5 5/8 below the door.
- STOW: legs up, B folded, steps lifted and latched, slide A home, pins in.
Caution Never drive with the steps unlatched or A unpinned.
Commission step 15
Load it
- Every test on the Test page.