TopeLeave about Dec 1

Systems / Outside / Slide-out deck

Slide-out deck

Under the door: a fold-out step, or a two-leaf deck from box to box.

8 TBD · 15 ready to order · also: AwningUnderbody boxesGrey water

Tape the crossmember height, check the slides, pick the face finish; then every part in build order.

1 Measure 0 of 5 done

What the drawing still guesses. Type what you get; it goes to Claude with your other changes.

Crossmember slot

Width of the 2 in slot and how deep it goes, at CM1.

Sets: Clamp plates for the crossmember slots, 1/4 steel, 2 x 3, Heavy locking slides, 22 in, about 550 lb a pair, black

Crossmember bottoms to the ground

Taped at the deck bay, on level ground: the deck top lands 1 3/8 in below them.

Sets: Steps: TorkLift GlowStep Revolution 3-step, A8103, Marine plywood, 1 1/8 in, 4 x 8 (both leaves come out of one sheet)

The door

Its front and back edges from the back of the front box.

Sets: Steps: TorkLift GlowStep Revolution 3-step, A8103

Box door faces

Are the passenger box doors flush with the body edge? A straightedge along the body side.

Sets: Face bands, black aluminium, 1/8 x 1 1/8 (or black diamond plate), Skirt on A: 1/8 black aluminium (or diamond plate), with an open step well

Rear tire

How far its outer sidewall sits in from the body edge.

Sets: Leaf B, 51 x 22 marine ply

2 Settle

  1. Plain or diamond plate The face bands and the skirt can be plain black aluminium (sleek, quieter) or black diamond plate to match the boxes (reads as one more box). Which?
  2. Stored steps hang low Stored, the GlowStep's bottom is about 16 3/8 in off the ground, about 1 5/8 in below the box bottoms. Fine for ground clearance; if you want it tucked level with the box line, the step frame mounts higher at the cost of some of its height range.
  3. Landing feel On two 550 lb slides with the steps propping its edge the landing will give a little at its outer edge. If that bothers you, double the slides (two each end) before adding legs.
  4. R3 Drops from the crossmember at the back box's front edge. Check it clears the fill pipe there.

3 Parts in build order

8 TBD15 ready to order

Rails

TBDcut from stock

Clamp plates for the crossmember slots, 1/4 steel, 2 x 3

Buy and cut: Home Depot #4013 · qty 6

Slid into each crossmember's 2 in slot so the drop brackets bolt up with no drilling, the way the boxes hang. Two 3/8 bolts each.

TBD until: the slot's width and depth inside the crossmembers

ready to ordercut from stock

Drop brackets, 2 x 2 x 1/4 steel angle

Buy and cut: Home Depot #4013 · qty 4 ft

R1, R2: 3 1/8 to the slide; R3: 4

From the crossmember down to the slide's fixed member, beside or under the leaf, so nothing crosses the deck. Painted black.

TBDstock

Heavy locking slides, 22 in, about 550 lb a pair, black

Buy: OVIS (Fulterer FR5400 class) or Amazon (search) · qty 3 pair

22 in, full extension, lock-in and lock-out, side-mount, about 1/2 x 2 3/4

R1 and R2 on A's end bands carry the half deck on their own; R3 lies flat under B's free end. If the landing feels springy, double up: two slides at each end of A.

TBD until: a slide that locks both open and shut and fits flat beside A under a 4 in crossmember

Leaves

TBDstock

Marine plywood, 1 1/8 in, 4 x 8 (both leaves come out of one sheet)

Buy: Crosscut Hardwoods · qty 1 sheet

two 51 x 22 out of a 48 x 96 sheet; about 2.9 lb a sq ft in okoume, so about 22 lb a leaf

Both leaves the same: solid and quiet underfoot, easy to screw into and to repair. Sags about 1/4 in under one person across 51 in.

TBD until: 1 1/8 in stock; if not, laminate a 1/2 and a 5/8 marine sheet with epoxy

TBDcut from stock

Leaf A, 51 x 22 marine ply

Buy and cut: from the sheet · qty 1

end bands for R1 and R2, the face band, the skirt, the step well and the leg hinges hang off it

TBDcut from stock

Leaf B, 51 x 22 marine ply

Buy and cut: from the sheet · qty 1

grip on BOTH faces: its back is the half deck's landing

Rests on R3 at its free end, two pin-in legs for the full deck.

ready to orderstock

Marine epoxy (West System 105/205 or similar) and threaded inserts

Buy: Fisheries Supply / West Marine, or Amazon (search) · qty 1 kit, 30 inserts 1/4-20

Seal every edge and every hole: it lives in road spray. Inserts (E-Z Lok style, set in epoxy) wherever something bolts on and comes off again.

ready to orderstock

End bands, 2 x 1/4 aluminium flat bar

Buy: Home Depot #4013 · qty 4 ft

2 at 22: A's two ends. The slides' inner members bolt to them

TBDstock

Walking surface: marine EVA foam decking, 6 mm

Buy: SeaDek or Hydro-Turf (search) · qty 3 pieces 51 x 22

On A's top and both faces of B. Grippy wet or dry, soft underfoot, UV stable.

TBD until: faux teak or plain grey

TBDstock

Face bands, black aluminium, 1/8 x 1 1/8 (or black diamond plate)

Buy: Home Depot #4013 · qty 2 at 51

On each leaf's outer edge, flush with its top. Stowed, B's sits on A's: one 2 1/4 in black line, flush with the box doors.

TBD until: plain black or diamond plate, to match the box doors

ready to orderstock

Stainless piano hinge, heavy, 24 in

Buy: Amazon (search) · qty 1

On the top faces over R2: B folds face down onto A for the half deck, or flips back over the tire onto R3.

Steps

ready to orderstock

Steps: TorkLift GlowStep Revolution 3-step, A8103

Buy: Amazon / CAMPERiD · qty 1

25 1/2 wide, 7 1/2 rise, 375 lb, 25 1/2 to 32 from the opening to the ground: the half deck is 31 3/4, the full deck 30 5/8

Always on A: it rides out with the deck, drops with one lever, stands on its own adjustable landing gear and props A's edge. Stored, it collapses and latches in its own frame.

Before you order: it fits a 25 1/2 well and the stored package (about 8 deep, 14 tall) clears what is under A

ready to ordercut from stock

Step well frame: two 1 1/2 x 1/4 aluminium angles for the GlowStep's brackets

Buy and cut: Home Depot #4013 · qty 2 at 8

Bolted up into A's inserts at the outer edge; the GlowStep's factory brackets bolt to them, 25 to 25 1/2 apart.

Skirt

TBDstock

Skirt on A: 1/8 black aluminium (or diamond plate), with an open step well

Buy: Home Depot #4013 · qty 1 sheet, 24 x 60

51 long, 11 1/2 tall, a 1 in return along its bottom; the step well cut out, 26 wide

Rides out with A. Stowed it hides everything under the leaves and lines up with the box bottoms; out, it is the deck's skirt.

TBD until: the same finish as the bands

ready to orderstock

Skirt hangers: 1 x 1 x 1/8 aluminium angle

Buy: Home Depot #4013 · qty 8 ft

Two from each end band down to the skirt's bottom, and a return along the skirt's top under A's face band.

Legs

ready to orderstock

Leg tubes: 6061 round, 1 1/4 x 0.058 outer and 1 1/8 x 0.058 inner (they telescope)

Buy: OnlineMetals or Amazon (search) · qty 4 of each, 18 in

outer 18, inner 18, 1/4 holes every inch in the inner; they reach 28 1/2

Tubes 1/8 apart in diameter in the 0.058 wall telescope with a sliding fit.

ready to ordercut from stock

Leg hinges for A's two: angle cheeks and a 5/16 shoulder bolt

Buy and cut: Home Depot #4013 · qty 2 sets

Into A's inserts at its two outer corners. The legs fold inward, across the leaf, clear of the step well.

ready to orderstock

Ball-lock pins, 1/4 x 1 1/2, stainless, with lanyard

Buy: Amazon (search) · qty 6

ready to orderstock

Levelling feet, 3/8-16 stud, 2 in swivel pad

Buy: Home Depot #4013 · qty 4

ready to orderstock

Locking folding braces, 10 in, black

Buy: Amazon (search) · qty 2

Hold A's legs vertical; push the knee to fold.

ready to ordercut from stock

Flush leg receivers for B, bonded into its outer edge

Buy and cut: Home Depot #4013 · qty 2

Flush with B's back, because folded that face is the landing: nothing to trip on. B's two legs pin in for the full deck; clipped under A otherwise.

ready to orderstock

Spring clips, rubber lined, for 1 1/4 tube

Buy: Amazon (search) · qty 4

Hold A's folded legs, and B's two when they are off.

ready to orderstock

Travel locks: a pin through each rail

Buy: Home Depot #4013 · qty 3

Belt and braces on top of the slides' own lock-in.

Tap a card to find it here. Tap a part to find its card.