TopeLeave about Dec 1

Systems / Water / Grey water

Grey water

Kitchen and shower drains to the ground or a tank, through two fail-safe valves.

7 TBD · 15 ready to order · 2 ordered · 14 have it · also: Underbody boxesDeckAC

Three stages in order: the kitchen sink to the ground, the shower to the ground, then the grey water box, valves and tank. The drawing builds up as you scroll.

Build

Every step in order. Scroll and the drawing follows: it builds up to the step you are on and lights what that step adds.

Kitchen to the ground steps 1 to 5

1

The holes

  1. Plumb from the strainer: 48 in back from the cab wall, 11 1/2 from the driver wall. Look underneath first: it lands mid-gap between crossmembers C and D, clear of the pilot.
  2. 2 1/2 in hole through the cabinet floor. Hang a plumb string through it, then a 2 1/8 in hole through the truck floor, half from each side on one pilot.
  3. Seal the bare wood of the truck-floor hole with the PL S30 and let it cure before any pipe goes in.
2

Tailpiece and the RO saddle

  1. The white strainer stays. The flanged tailpiece's flange and washer go inside its slip nut; the nut screws onto the strainer's threads, hand tight.
  2. Drill a 1/4 in hole in the tailpiece about 1 1/2 in below the nut, clamp the iSpring saddle over it, push in the RO's waste line.
  3. Keep at least 3 in of tailpiece below the nut for the saddle. If the HepvO needs to sit lower, add one 6 in extension tube under the tailpiece on its own nut.
3

The HepvO and the tube below it

  1. The HepvO on the tailpiece, upright, arrow pointing down, its nuts hand tight.
  2. The 12 in tube into its bottom nut. Leave it long for now: it is cut on the dry fit in the next step.
4

Fernco and the straight drop

  1. Dry-fit: the Fernco on the tube, then one straight piece of PVC from its bottom down through both holes, ending about 2 in below the truck floor. Mark, cut the tube and the PVC.
  2. No cleanout under the sink: a straight drop barely clogs, the HepvO comes apart by hand, and loosening the Fernco opens the drop from above for a snake.
  3. Nothing is glued in this stage: the slip nuts are hand tight, the Fernco is clamped. Strap the pipe to the cabinet back with screws only: the straps hold it up, not the floor.
5

Under the truck: screen the end

  1. A square of metal window screen folded over the pipe's end, a hose clamp an inch up. Water runs out, bugs and road dirt stay out.
  2. Once the PL on the hole's wood has cured, silicone round the pipe at the truck floor: it cuts out clean.
  3. To pull it: unscrew the straps, cut the silicone, loosen the Fernco, lift the pipe up into the cabinet.
  4. Fill the sink and pull the plug: every joint dry with a paper towel, water out through the screen.

Tope Later the screen comes off, a Fernco 1056-150 goes on the end, and the line to the box pushes into it, with the cleanout at the turn under the truck. Nothing above changes.

Shower to the ground step 6

6

Shower drain, trap and drop

  1. Built in the shower guide: the drain drops into the 8 in channel behind where the valve box will hang, the HepvO runs aft in it.
  2. Its waste leg goes down through the truck floor the same way as the kitchen: the hole's wood sealed with PL first, the pipe ending 2 in below the floor with a metal screen clamped over it, silicone round it at the floor. It drains to the ground.
  3. Run the shower 5 minutes: every joint dry, water out the bottom.

Tope Later the screen comes off, a Fernco goes on, and the shower's line to the valve box pushes into it. Where the leg comes through the floor comes off the shower guide: tape it before drilling.

Grey water: box, valves, tank steps 7 to 16

7

Check the valves before buying

  1. Ask U.S. Solid: is there a manual override on the 1 1/2 in 2-wire auto-return valve, and what does it draw while held?
  2. The T-1600's ports: an inlet you can use on its front end and a drain at the low aft corner.
8

The valve box goes up first

  1. The driver front Buyers box, 24 x 14 x 16, under the shower: built on the Underbody boxes guide. The valves, the wye and the outlet live in it.

Tope Hang the box before cutting any pipe: the pipe positions come off the real box.

9

Kitchen line and cleanouts

  1. Screen off the kitchen drop, a Fernco 1056-150 on its end; the line pushes into it, with a cleanout at the turn (the tee, adapter and plug from the first order), plug reachable from underneath. Under the floor the kitchen line turns forward and runs just under the crossmembers, over the tank, into the box's aft end.
  2. About 1 1/2 in over the tank top. Falling all the way, strapped every couple of feet, never hanging off a valve.
  3. Cleanouts at the kitchen turn under the truck, on the shower leg and on the wye inside the box.

Caution No sags: a dip holds water, and that is where it starts to smell.

10

The valve manifold, in the box

  1. Both lines meet in a wye just inside the box. Under it a tee: V1 straight down through the box floor, V2 aft out of the box toward the tank.
  2. Unions on both valves, so either comes out without cutting pipe. V1's override faces the door.
11

Ground outlet

  1. Under the box floor: a short drop to a screen and a duckbill, about 16 in off the ground.
12

Switch panel and wiring

  1. GROUND: no power, V1 open, V2 shut. TANK powers both: V1 shuts, V2 opens. DUMP opens V3.
  2. The level sensor's 95 percent contact cuts TANK. Own fuse. A broken wire means Ground.
13

Cradle and straps

  1. A cradle the tank's full length, two straps clamped into crossmembers C and D with plates in their slots: no drilling the frame.
  2. Tilt it a little aft, toward the drain corner.
14

Tank: lid, rinser, vent, level

  1. The 6 in deck plate on the outboard edge of the top, the rinser beside it.
  2. Its own vent with the carbon filter, out at the skirt. The inlet from V2 into the front end, high.
15

Dump and drip

  1. V3 at the low aft corner, pointing out where a hose reaches. V4 beside it, pointing down.
16

Test it

  1. Every test on the Test page before anything closes in.
Scroll the steps: the drawing follows. Tap a part to find its step.