TopeLeave about Dec 1
← Kitchen build 1/29
← Kitchen

Kitchen build

Galley, driver wall29 steps

The galley from the partition to the Happijac pillar, 56 in of driver wall: base cabinets, drawers, counter, sink and faucet, RO, uppers, the window panel, trim, lights, and a positive latch on every drawer and door.

Where it stands, 2026-09-30Already in the 2026-07-01 photos: two base carcasses with their oak-effect fronts and edge pulls (a three-drawer bank by the partition, a two-door sink base), a 3/4 ply counter with the sink cutout, the black composite sink sitting in it, and two fluted upper cabinets hung on top of the window panel line.The window panel is cut and dry-fit (2026-08-07, 56 x 27 7/8, 41 3/4 x 15 cutout) and its poplar rail frame is glued. Keeper steel, black anodised angle, the warm LED strip, aluminium channels, the two straight stops and the PEX valves are bought.Not done: drain, supplies, faucet, RO, travel latches, lights, trim, the panel's microcement. Nothing is decided for cooking. kitchen.html says the HI-MACS top is installed; the photos show bare ply. Confirm which.ASSUMED on this page, tape before relying on it: counter 36 high, carcass 19 1/2 deep and 30 tall on a 4 3/4 toe space, drawer bank 15 wide, sink base 36, sink centre 52 in aft, uppers 14 3/4 deep from 63 7/8 to the ceiling, the 8020 stations, the 11 in speaker gap.
Order list9 now, 10 after a check, 5 not yet

Prices as last seen; check before paying. "After a check" names the check in the step list.

Order now9

Order now~$22
Poplar 1x2, 6 ft

Floor cleats under the plinth (2 runs of about 53 in) and the board slot's stops.

Order now$15 listing
G5 sink basket strainer

Mandatory: grease sets in a cold underfloor line. Size it to the composite sink's drain hole (usually 3 1/2).

1 · Amazon
Order now$35.20
G6 HepvO waterless trap, 1 1/2 in, 5717

No water seal to slosh out on washboard. Same part as the shower's.

Order now$5.98
1 1/2 in x 2 ft PVC DWV Schedule 40

From the HepvO down through H-9. The grey line below the floor is the water page's.

Order now~$10.94
PVC primer and cement

Purple primer and clear cement combo. One pack does the shower and the galley.

Order now$11.48
Neutral-cure silicone, clear

Sink rim, counter to panel bead, trim against aluminium. NEVER acetoxy (vinegar smell): it corrodes the anodised trim.

Or: DAP Silicone Max 08791 · $11.48Also neutral-cure, same price
Order now
3M Dual Lock (or hook and loop)

Holds the window panel flat, Jeff's 2026-09-01 scheme, in place of the magnets. Reclosable, so the microcemented panel comes off intact. NOT foam tape and NOT the VHB already bought: both take the face veneer with them.

~8 pads · Amazon (search)
Order now$329.99
Marshall Middleton II, Cream

Jeff's speaker, in the cubby between the aft upper and the Happijac. 9.05 W x 4.33 H x 3.86 D, 3.9 lb, IP67, Bluetooth 5.3, 3.5 mm aux in, 30+ hours. Charges on USB-C (5/9/12/20 V, 3 A).

Order now
1 in strap with a cam buckle, or Dual Lock

Across the cubby mouth above the lip, so 4 lb of speaker stays put on washboard.

After a check10

After a check
Push-button travel latches, keyless, 14 to 23 mm doors

A positive lock on every drawer and door: 9 on this page (3 drawers, 2 sink doors, 2 per upper). A push button shoots a bolt behind the carcass rail; it cannot open on a bump the way a magnet or soft-close runner does. Caliper the real fronts first: the range must cover them.

9 + 1 spare · Amazon
Or: RV Designer H241 · Southco M1, Fisheries SupplyHidden alternative if Jeff does not want buttons on the fronts: RV Designer H241 positive catch with 5/8, 3/4, 7/8 and 1 in strikes (releases with a firm pull, so less positive), or Southco M1-63 flush latch (fits only 12 to 17 mm fronts, $26.72 each).
After a check
Accuride 3832EC 18 in full-extension slides

Only if the drawer bank's own runners come out (step 12). 100 lb, hold-in detent, lever disconnect, 1/2 in side space each side. 18 in suits the 19 1/2 carcass. The latch, not the slide, is what holds the drawer on the road.

After a checkcall
1/2 in Baltic birch, 5 x 5

Drawer boxes, only if they are rebuilt. A 5 x 5 yields all three boxes' sides, fronts and backs.

After a checkcall
1/4 in Baltic birch, 5 x 5

Drawer bottoms, let into a 1/4 groove.

After a checkcall
3/4 ply for the plinth ladder, end panel and slot

Only where the photos do not already show legs and a plinth. Birch, half sheet.

After a check
8020 drop-in T-nuts, 10 series, 1/4-20

Brackets to the 8020 without sliding nuts in from an end that is already closed in. Or use the #8 x 1 sheet metal screws Jeff already furred the walls with.

After a check$70 listing
G4 kitchen faucet, single lever

The water page's pick. Check its supply tails end in 3/8 compression before buying, so they go straight onto the stops (the G3 audit note). If the RO500AK box has no tap (R2), pick a faucet with a filtered side and use one hole.

After a check
MS polymer sealant

The one joint that may be re-coated: the window panel's microcement edge against the shower wall's. Nothing sticks to cured silicone.

After a check
Microcement for the window panel

CimentART, the shower's brand, so the panel matches the wall beside it. Their plywood sequence; seal the bottom edge and back.

After a check
12 V USB-C PD socket, panel mount, 60 W

Keeps the speaker charged in its cubby, off the 12 V lead that already runs up to the uppers, on its own fuse. Pick one with an off switch or low standby draw.

Have it8

Have it
#8 x 1 sheet metal screws

Bought 2026-09-02 for furring into the 8020. Same use here for the bracket legs.

Home Depot 4040 00053 09059
Have it
Straight stops, 1/2 PEX x 3/8 compression

G1 and G2 (galley isolation) and G3 (faucet connection) in one part each, Jeff's find. Bought 2026-09-15.

2 · Home Depot 4040 00080 18830
Have it
1/2 in PEX barb ball valve, brass

R1, the RO feed's own shutoff. From the jar bought 2026-09-11 or 2026-09-15.

1 · Home Depot (jar)
Have it
PEX tee, crimp rings

The RO tee off the cold line. From the jars of 25 and 100.

1 + 4 · Home Depot 4013 00053 15965
Have it
2 in hole saw

H-9 through the 2 1/4 floor for 1 1/2 PVC (1.90 OD). Jeff owns a 2 in. Cut from both faces on one pilot.

Have it
Black anodised angle, 1/2 x 1/2 x 3/64

E4 at the Happijac and spare for the panel edges. Bought 2026-08-18, about 39 ft.

Wholesale Glass & Supplies 189513
Have it
Keeper steel and #10 flat-head screws

Bought 2026-08-10 for the magnet scheme. Only needed if the panel goes back to magnets.

Home Depot 4013 00053 06824
Have it
Warm LED strip, BTF FCOB 2700K 528/m 12 V, and aluminium channels

Bought 2026-08-13 (strip) and owned (channels with tinted covers). Under-cabinet and toe-kick warm runs.

Not yet5

Not yet
RGB strip, BTF FCOB 810/m 12 V

The second strip in each dual channel: red at night, colour for party. One 16.4 ft reel covers galley and bed. Waits on the full lighting map.

1 reel · Amazon (search)
Not yet
Task pucks, 3000K CRI 90+

Two under the uppers over the prep counter. Product open on the lighting page.

Not yet
LED controller

One central (QuinLED) or per zone (Gledopto). Decided with the full lighting map.

Not yet
Cooktop

Nothing chosen. Induction on the 810 Ah bank is the obvious candidate (a portable one stores in the bottom drawer). Jeff decides; the page only reserves a zone.

Not yet
Dometic UFM flush-mount frame 9620012874

For the NRX50E, IF it goes in the galley. Nothing says where it goes, and the measure sheet says NRX 35E.

Cut list22 parts

Inches. "Field-fit" means cut to the thing it meets, on the day.

partstockqtysize
Floor cleatspoplar 1x22~53 11/16front and back, inside the plinth ladder
Plinth front (toe kick)3/4 ply155 11/16 x 4 3/4set back 3 from the fronts; the LED channel rides above it
Plinth back rail3/4 ply155 11/16 x 4 3/4screwed to the back cleat
Plinth cross members3/4 ply415 x 4 3/4under every carcass side
End panel at the pillar3/4 ply119 1/2 x 301/4 clear of the Happijac, never touching it
Board slot floor3/4 ply13 15/16 x 19 1/2cutting boards and trays stand in it
Filler frontto match the fronts14 11/16 x 24leaves a 6 in hand slot at the bottom; field-fit
Drawer box sides1/2 Baltic birch618 x 8, 6, 4two of each height
Drawer box fronts and backs1/2 Baltic birch611 11/16 x 8, 6, 4between the sides; rabbet or screw and glue
Drawer bottoms1/4 Baltic birch312 3/16 x 17 1/2in a 1/4 x 1/4 groove
Counter substrate3/4 ply (in place)155 3/4 x 21 1/2in the July photos with the sink cutout
Backsplash stripHI-MACS offcut or to match155 3/4 x 3ASSUMED height; it hides the panel's bottom edge
Window rail framepoplar 2 x 1 1/2, laminated8 strips2 @ 49, 2 @ 20 1/2, 2 @ 24 1/2, 2 @ 45DONE 2026-08-07, glued round the blind cassette
Window panel1/4 Baltic birch156 x 27 7/8, cutout 41 3/4 x 15DONE 2026-08-07; radius the cutout corners
E4 angle1/2 x 1/2 black anodised (have)127 7/8VHB to the Happijac side only
Speaker cubby floor and top1/2 Baltic birch210 3/4 x 14 3/4cubby width ASSUMED: tape the gap first
Speaker cubby cheek1/2 Baltic birch114 3/4 x 11 3/8the aft side, 1/4 clear of the column
Speaker cubby back1/4 ply110 1/4 x 11 3/8USB-C socket hole low and aft
Speaker cubby lipoak110 1/4 x 1 1/2 x 1/2glued and pinned across the floor's front
Top trim / U-bracketaluminium, black anodised155 3/4carries the under-cabinet channel in its front leg
Toe-kick channelaluminium (owned)1~54 3/16warm + RGB side by side
Under-cabinet channelaluminium (owned)1~54 3/4in the U-bracket, never on the panel

Measure and decidesteps 1 to 4

    1. Counter top above the vinyl at both ends and the middle (D1 on the measure sheet). The page draws 36.
    2. Carcass depth, height and toe space; drawer bank and sink base widths. The page draws 19 1/2 deep, 30 tall on 4 3/4 legs, 15 and 36 wide.
    3. Sink centre from the cab wall, and the sink's real size and drain hole. The floor plan read 35 3/16 off a photo; with a 15 drawer bank by the partition it cannot be there, so the page draws 52.
    4. Upper cabinets: depth, height, how they hang, and where the control box sits in them.
    5. The gap between the aft upper and the Happijac column, for the speaker cubby. The page draws 11; the speaker needs 10 13/16 with its cheek and a little air.
    6. Where the driver-wall 8020 runs behind the base and the uppers (uprights and horizontals). The page draws them ASSUMED.
    7. The window cutout's side margins: the notebook gives 14 1/4 total, the page splits it evenly.
    Caution Every number marked ASSUMED here was read off a perspective photo. Tape it before you cut anything to it.
    1. Cooking: nothing is chosen. Portable induction off the inverter, stored in the bottom drawer, used on the aft counter, is the page's placeholder only.
    2. NRX fridge: NRX50E or NRX 35E, and where. There is no room for it in this run as drawn; it would take the sink base's place.
    3. Latch style: a push button on each front, or a hidden catch. Caliper the fronts (the button range is 14 to 23 mm).
    4. HI-MACS: on already, or still to come? kitchen.html says installed, the photos show ply.
    Tope Decide cooking before the counter is finished: a built-in hob needs a cutout and a cable, and both are cheap now and hard later.
    1. Now: G5 strainer, G6 HepvO, 1 1/2 PVC, primer and cement, neutral-cure silicone, Dual Lock, poplar 1x2 (Order list, top).
    2. After the caliper: 9 push-button latches plus a spare.
    3. After the faucet check: G4, only if its tails are 3/8 compression to suit the stops you already have.
    4. Already here: both straight stops, the PEX valves and tees, warm strip, channels, black angle, keeper steel.
    Tip Open the RO500AK box before buying a faucet. If its tap is inside, the counter needs a second hole, not a two-way faucet.
    1. Tape a cardboard button where each latch would go: top centre of each drawer front, inside top corner of each door.
    2. Open each drawer fully and check the bolt clears the carcass rail and the counter's underside.
    3. Swing the sink doors and check the latch does not hit the stops, the PEX or the RO.
    4. Upper doors: check the latch at the bottom edge is reachable over the faucet.
    Tip One latch per door is enough on a short door. A tall door that flexes wants two.

Base cabinetssteps 5 to 8

    1. Two 1x2 poplar cleats on the floor, front and back, running the full 55 11/16.
    2. Screw them down with #8 x 1 1/4 at 8 in. That just bites the 1/2 birch subfloor; the 1 in XPS under it holds nothing, so nothing longer.
    3. The 3/4 ply plinth ladder on the cleats: front board 3 back from the fronts, back rail, a cross member under every carcass side. All 4 3/4 tall.
    4. Shim it level along and across. The counter is only as flat as this.
    Caution Look underneath before any screw: the plinth sits over the H-9 drain position and the PEX risers.
    1. Drawer bank, 15 wide, hard against the partition with 1/16 to spare. Sink base, 36, beside it.
    2. Bolt the two carcasses together through their shared sides, front and back, with connector bolts. One stiff box rides the road better than two.
    3. The photos show both standing already with fronts on. If they are only dry-set, pull the fronts and do this step and the next before anything else.
    4. Square each one by its diagonals.
    1. Angle brackets inside each carcass's top back rail into the driver-wall 8020: drop-in 1/4-20 T-nuts, or the #8 x 1 sheet metal screws used for the furring.
    2. Screw the carcass bottoms down into the plinth ladder, and the plinth into the cleats.
    3. Drawer bank side to the partition: #8 x 7/8 at most, from inside the carcass. 5/8 side plus 1/2 partition is 1 1/8; a 1 1/4 screw comes out in the shower.
    4. Nothing projects from the partition's galley face: the D1 frame and the drawers both need it flat.
    Caution No screw through the partition. Its shower face is waterproofed; a point through it is a leak behind the drawers.
    1. The 4 11/16 left between the sink base and the pillar becomes a slot for cutting boards and trays.
    2. 3/4 ply end panel screwed to the plinth and the sink base, 1/4 clear of the Happijac. Nothing touches the column.
    3. Slot floor on the plinth; the filler front comes with the other fronts.

Rough-insteps 9 to 11

    1. Mark H-9 under the sink drain, about 51 aft and 11 3/16 out from the driver wall. Check below first.
    2. 2 in hole saw from the top on a pilot, then from below on the same pilot: the floor is 2 1/4 thick.
    3. 1 1/2 PVC up through it, sealed at the floor, cut 2 in above the carcass bottom. The grey run below is on the water page.
    4. Leave it capped until the HepvO goes on.
    Caution The driver chassis rail is about 25 in from the driver wall. H-9 at about 12 in is clear of it, but look.
    1. 1/2 PEX hot (red) and cold (blue) up into the back of the sink base, crimped.
    2. A straight stop on each (G1 cold, G2 hot): PEX one side, 3/8 compression to the faucet the other.
    3. A tee in the cold below its stop, then R1, the RO's own ball valve.
    4. Pressure test with the pump on before anything closes in. No drips after 10 minutes.
    Tip Leave the stops low and to the back, where they can be reached with the RO in place.
    1. Toe-kick lead: through the end panel to the plinth front.
    2. Under-cabinet and task puck leads: up behind the end panel to the U-bracket line.
    3. Any outlet at the counter (USB-C, 12 V): decide now and pull its cable.
    4. Label both ends, leave 12 in loops, pull string beside each. Fused at the bus.
    Caution LED never mounts on the removable window panel. Every lead ends in the carcass or the U-bracket.

Drawerssteps 12 to 13

    1. If the bank's own runners are sound, keep them: the latch, not the slide, holds the drawer on the road.
    2. If they come out: Accuride 3832EC, 18 in, 1/2 in each side. Carcass member to the front edge, set back by the front's thickness.
    3. Screw both sides of each pair at the same height off a spacer block, not by eye.
    4. Load each drawer and drive a bumpy road before trusting it.
    1. Only if rebuilt: 1/2 Baltic birch, 12 11/16 wide over the sides, 8, 6 and 4 tall, 18 deep.
    2. Glue and screw, bottoms in a 1/4 groove, square by the diagonals.
    3. Heaviest things in the bottom drawer: it sits lowest and closest to the floor.

Counter and sinksteps 14 to 18

    1. 3/4 ply, 55 3/4 x 21 1/2, with the sink cutout: in the July photos already.
    2. Screw it up from below through the carcass top rails, #8 x 1 (5/8 rail plus 3/4 ply: a 1 1/4 shows on top).
    3. 1/4 reveal at the Happijac end. Check it flat with a straightedge; shim at the rails if not.
    1. Follow the fabricator's bonding and seam spec. Hold off if the photos are current and it is not on yet.
    2. Backsplash strip at the back edge, about 3 in tall: it hides the window panel's foot and is caulked to it.
    3. Neutral-cure silicone between the splash and the panel: this is the joint you cut to take the panel out.
    Caution kitchen.html says installed, the photos say ply. Confirm before ordering or cutting anything for it.
    1. Neutral-cure silicone under the rim, clips from below, wipe the squeeze-out.
    2. G5 basket strainer in the drain hole, tightened from below.
    3. G6 HepvO straight down from the strainer tailpiece onto the H-9 PVC. Vertical, arrow down.
    4. Fill the bowl, pull the plug, watch every joint.
    Tip A HepvO has no water seal to lose on washboard, and no smell when the truck sits for a month.
    1. Faucet through its hole behind the sink, gasket down, nut from below.
    2. Its supply tails straight onto the stops' 3/8 compression outlets. No extra connectors.
    3. Open the stops slowly, run hot and cold, check below with a dry paper towel.
    1. iSpring RO500AK, 17 1/2 x 5 3/16 x 16 1/4, against the back of the sink base, aft of the drain. Strap it to the carcass back and bottom.
    2. Feed from R1. Reject to the grey line upstream of the diverter (R3) or out through H-15, per the water page.
    3. Its tap (R2, probably in the box) through a second counter hole beside the faucet.
    4. Flush the filters to the manual before drinking.
    Tip Leave room in front of it to change the cartridges without unplumbing.

Uppers and the wallsteps 19 to 23

    1. The two fluted uppers hang in the photos. Find what holds them: each needs screws into the 8020 or the ceiling hoop ribs, not the wall panel.
    2. Their bottoms sit on the window panel line, 63 7/8. Nothing may bear down on the panel: it only rests on the counter.
    3. Load each with what it will carry and push hard on the front edge.
    Caution A loaded upper cabinet is the heaviest thing above head height in the truck. Fix to structure, never to ply alone.
    1. An open box, 11 wide (ASSUMED, tape the gap), between the aft upper and the Happijac, the same depth and height as the uppers. 1/2 Baltic birch.
    2. Screw it to the aft upper's side and through its back into the 8020. Its aft cheek stands 1/4 clear of the column: nothing fixes to the Happijac.
    3. A 1 1/2 oak lip across the front of the floor, and a strap or Dual Lock across the mouth above it. The Middleton sits upright on the floor, grille to the aisle.
    4. USB-C PD socket in the back, fed from the 12 V lead that comes up to the uppers, on its own fuse. Leave the cable just long enough to reach the speaker's port.
    Tip It is IP67, so a splash from the sink does no harm; the strap is the part that matters.
    1. The glued poplar frame, 49 x 24 1/2 outside, 45 x 20 1/2 inside, round the blind cassette (done 2026-08-07).
    2. Fix it to the wall structure round the window. The panel lands flush on its 2 in face.
    3. With Dual Lock the magnet groove is not needed. If magnets stay, settle the keeper conflict first: the bar bought is 3/4 x 1/8, so the groove becomes 1 in x 5/16.
    1. Microcement the room face on the bench (CimentART, the shower's brand). Seal the back and every edge, the bottom edge most: it stands in a pocket that cannot dry.
    2. Dual Lock pads on the frame and the panel back, about 8. Not foam tape, not VHB.
    3. Stand it on the counter, press it onto the frame. The counter carries its 11 lb; the pads only stop it drumming.
    4. Caulk the backsplash joint.
    Tip Taking it off: cut the caulk, swing the bottom out, lower it from the top trim. It moves as one stiff piece and the finish survives.
    1. Black anodised U-bracket under the uppers along the panel top: it steadies the panel's top and carries the under-cabinet channel in its front leg.
    2. E4 at the pillar: the 1/2 x 1/2 black angle, 27 7/8 long, VHB to the Happijac only, floating over the microcement.
    3. Shower side: MS polymer in the seam, no trim, so the microcement can be touched up one day.
    4. Every bead neutral-cure. Confirm which edge is the Happijac one and which is the shower before cutting trim (the notes say left for both).
    Caution Acetoxy silicone (vinegar smell) corrodes the aluminium and will not bond to microcement.

Lightssteps 24 to 25

    1. Aluminium channel on the plinth top, just behind the fronts, washing the floor.
    2. Two strips side by side: the warm 2700K (have) and the RGB (held). Red at night, warm on the chill scene.
    3. Test on scrap first; set the channel from a real piece.
    1. Warm and RGB strips in the U-bracket's front leg, washing the window panel. Nothing on the panel itself.
    2. Two task pucks, 3000K CRI 90+, under the uppers over the prep counter by the partition (about 28 and 38 in aft), on their own switch leg.
    3. Leads to the controller, which waits on the full lighting map.

Finish and travelsteps 26 to 29

    1. Rehang the fronts, set the gaps even at 1/8, tighten every hinge screw.
    2. Filler front on the board slot, with a hand gap at the bottom.
    3. Check every drawer and door clears the others fully open.
    1. 9 push-button latches: 3 drawers, 2 sink doors, 4 upper doors. Drill to the template, bolt behind the carcass rail.
    2. Soft-close runners and magnets are not latches. Every opening that can swing or slide gets a bolt.
    3. The board slot gets a bungee or a turn button across its mouth. The speaker cubby gets its lip and strap.
    4. Push each closed and pull hard: nothing may move.
    Caution A drawer of cans that opens under braking is a hazard, not a mess. No exceptions, including the small ones.
    1. CFX3 75DZ in the passenger bench: secure the lid (Jeff's Thursday list) and lock the slide closed for travel.
    2. Nothing fixed in its forward slide travel: the floor plan flags a possible clash with the passenger Happijac column (tape B14 and C8).
    3. NRX: placement still open; nothing in this run is cut for it.
    1. Run the sink full, hot and cold. Run the RO to the manual. Check every joint dry under the sink after a day.
    2. Open and close every drawer and door twenty times; latch everything and drive a washboard road.
    3. Re-check the bracket screws, the latches and the sink clips after the first week.
Notes11
  • Where the galley is: floor plan (along the driver wall from the partition to the forward Happijac pillar, 56 in, set by the measured 56 in window panel) and 3D interior (heights). Earlier pages said 50 in from layout.html; the panel overrules it.
  • ASSUMED on this page: counter 36; carcass 19 1/2 deep, 30 tall, 5/8 boards on a 4 3/4 toe space; drawer bank 15 and sink base 36 wide (photo read); sink 17 x 14 centred 52 aft; uppers 14 3/4 deep, 63 7/8 to the ceiling, two doors each; 8020 stations behind the run; the window cutout centred; HI-MACS 12 mm.
  • The cabinets in the photos look like flat-pack (IKEA style, oak-effect fronts with edge pulls, fluted uppers). If so, their own legs and runners may replace the plinth ladder and the slides drawn here; the latches and the fixing to the 8020 are still needed.
  • Conflict: the floor plan puts the sink centre about 35 in aft from a photo, but the photos also show a drawer bank of about 15 in by the partition, so the sink sits further aft, over the sink base's door joint. This page draws 52.
  • Conflict: kitchen.html says the HI-MACS countertop is installed; every galley photo (2026-07-01) shows bare 3/4 ply.
  • Conflict: the window panel page section 8 (2026-09-01) changes the panel's hold from magnets to reclosable tape, but section 9 still lists the magnet groove as blocking. This page follows section 8 (Dual Lock); the groove only matters if magnets come back.
  • Partition: the bathroom door page says drawers run the partition's galley face, so nothing may project there. Here that is the drawer bank's side against it; screws from the kitchen side stop short of the waterproofed shower face.
  • Plumbing ids are the water page's: G1 and G2 galley isolation, G3 faucet connection (all three done by the two straight stops), G4 faucet, G5 strainer, G6 HepvO, R1 RO feed valve, R2 RO tap, R3 reject tee, H-9 galley drain, H-15 RO reject. See the water system.
  • Lighting follows the lighting plan and planning/walls-trim-lighting.md: task pucks under the uppers over the forward third of the counter, dual warm + RGB strips under the cabinets and in the toe kick, nothing on a removable panel.
  • Fridges: the CFX3 75DZ lives in the passenger lounge bench, not this run. The NRX (50E in context.md, 35E on the measure sheet) has no location.
  • Cooking: kitchen.html says "Not documented yet". The reserved zone aft of the sink is a placeholder for Jeff's decision.