TopeLeave about Dec 1
← Lounge build 1/25
← Build guides

Lounge build

Benches, lids, cushions, windows, panels, table25 steps

The J of benches at the back of the box: three bench boxes over the fridge, the water bay and the dog food, their lids and hinges, the window frames and wall panels, cushions and backrests, the table, and the bed that comes down over all of it.

Where it stands, 2026-09-30BUILT (09-28 video): the three bench boxes stand, white, with their lids on and a sheepskin over them; the wall panels are up; the table is on its post; the rear wall has its two black channels. Fridge in the passenger bench, tank placed in the rear bench.THURSDAY 10-01 (Jeff's list): fit a hinge on the lounge, trim the lounge lids, secure the fridge lid. Steps 6, 9 and 10.BOUGHT: four 3 in matte black utility hinges (HD, 08-10), 60 ft of 1x5 poplar rail stock (Mr Plywood, 08-06 and 08-10), black anodised 1/2 in angle (WGS, 08-18), 1/8 Baltic birch. Nothing yet for cushions, stays or latches.NOT MEASURED: the lounge window openings (the frames wait on them), the bed-down height over the benches, the aft Happijac columns. Foam thickness and fabric are open. The lip light and the two Sirocco fans wait on the full lighting map.
Order list3 now, 7 after a check, 4 not yet

Prices as last seen; check before paying. "After a check" names the check in the step list.

Order now3

Order now$4.27 (listing)
Everbilt 3 in matte black utility hinge, 2-pack, 28947

Three lids open (dog food, rear pocket, rear tank) at two hinges each: six. Four are in hand, so one more pack.

Order now$5.27 (listing)
Felt pads, 3/4 in heavy duty, Everbilt 822871

Under each lid where it lands on the front and the crossrail: stops the lids drumming on washboard.

Order now
Split loom, 1/2 in, flame retardant, 25 ft

The bed light cable inside the benches, from the column slot to the forward end of the dog food bench.

After a check7

After a check
Lid stays, soft-close, 105 degree, 2-pack

One per opening lid, three lids, so two packs. Rated 3 to 10 lb each: weigh a lid with its cushion first; the long rear tank lid may want two.

Or: Richelieu BP5010512GOr a Richelieu flap stay (hold-open and soft-close, 15 lb)
After a check
Southco M1-2A pop-out flush knob latch

Travel latch in the front edge of each opening lid; the cushion alone will not hold a lid shut on a hard stop. Listed for 1/2 to 3/4 doors: measure the real lid first.

After a check
Edge banding, birch, pre-glued, 3/4 in x 50 ft

Only if the trimmed lids show raw ply edges. If the lids are white melamine, buy white banding instead.

After a check
Seat and backrest foam, HR (high resilience), 4 in seat

Cut list below. IN-EX cuts it to size in-store; take the cut list. Thickness after the sit test (step 3).

Or: The Foam Factory · Foam Warehouse NWOr online, cut to the list
After a check
Dacron wrap, 1/2 in

Round each seat block: fills the cover and softens the edge.

After a check
Non-slip pad under the cushions

Cut to each cushion: stops them walking off the lids on the road.

After a check$39.99 (listing)
IRIS airtight pet food bins, 12 + 33 qt

For the dog food bench. Check the 33 qt height against 19 in under the lid before buying.

Have it7

Have it
Everbilt 3 in matte black utility hinges, four

Bought 2026-08-10 (two 2-packs). Four of the six.

4 · Home Depot #4013 (receipts/README.md)
Have it
1x5 poplar, rail stock

60 ft bought (08-06 and 08-10). The kitchen frame used 23 ft 2 in of strip; both lounge frames need about 41 ft more. Count what is left before cutting.

Mr Plywood (receipts/README.md)
Have it
Black anodised angle, 1/2 x 1/2 x 3/64

About 39 ft, Wholesale Glass, 2026-08-18. E4 at the columns.

Wholesale Glass (planning/walls-trim-lighting.md)
Have it
Keeper steel flat bar, 48 x 3/4 x 1/8

Bought 08-10 for the kitchen panel's magnet keepers; same system here.

Home Depot #4013 (receipts)
Have it
#8 x 3/4 and #10 zinc screws

From the 08-10 and 09-30 Home Depot runs: cleats, strips, hinges (the hinges want #8 x 5/8 into 3/4 ply).

Home Depot #4013 (receipts)
Have it
Dometic CFX3 75DZ and its slide

In the passenger bench.

1 · in the truck
Have it
Table and its post

In the truck (09-28 video). Model not recorded.

1 · in the truck

Not yet4

Not yet
Cover fabric

Jeff's pick. Wants to be tough, washable and dog-proof: a solution-dyed outdoor fabric like Sunbrella reads right. About 7 yd at 54 in for seats and backs.

Not yet
Caframo Sirocco II, black, 12/24 V, 7010CABBX

Two, blowing into the lounge. Where they mount is not decided (step 19), and that decides their wiring.

Or: SEEKR by CaframoSame fan, maker's page
Not yet
BTF FCOB RGB strip, 12 V, 810/m, 10 mm, IP30, strip only

The rear bench lip, with the warm strip already bought. One reel covers the bed and the lip. Waits on the lighting map.

1 reel · Amazon
Not yet
Shelly BLU Button1

The dimmer at the bed, stuck up in the lounge. On the bed guide's list too: buy once.

Cut list22 parts

Inches. "Field-fit" means cut to the thing it meets, on the day.

partstockqtysize
Fridge lid (secured)3/4 ply (as built)139 5/16 x 19 11/161/8 lip over the front; screwed down, not hinged
Dog food lid3/4 ply (as built)127 13/16 x 19 11/161/8 lip over the front and the forward end
Rear lid 1, core pocket3/4 ply (as built)116 9/16 x 33joint lands on the crossrail
Rear lid 2, tank3/4 ply (as built)116 9/16 x 47 3/8longest lid: weigh it for the stay
Back strip, passenger3/4 ply139 x 3width ASSUMED; panel stands on its back edge
Back strip, driver3/4 ply127 3/8 x 3
Back strip, rear3/4 ply180 1/2 x 3full width, corners included
Wall ledgers3/4 x 3 ply or poplar339, 26 5/8, 79under the strips, into the 8020 or the ply
Floor cleats3/4 x 1 1/2338, 26 1/8, 79 1/2inside each front; screw sideways into the front, down into the 1/2 ply
Rear crossrail3/4 x 1 1/2116 1/4under the rear lid joint, on edge
Lip railwhite oak 3/4 x 1 1/2135 1/4rear bench front, open middle only; groove the underside for the channel (held)
Window rail, longpoplar strip 2 x 3/4838two layers per rail, half-laps staggered; size from the MEASURED opening
Window rail, shortpoplar strip 2 x 3/4820between the long rails; same
Wall panel, passenger1/4 Baltic birch (ASSUMED)159 5/8 x 43 3/8window cutout 33 x 19, from a template
Wall panel, driver1/4 Baltic birch (ASSUMED)147 3/8 x 43 3/8same cutout; DS wall is the taped 47 3/8
Seat foam A1, passenger full runHR foam159 x 22 5/8 x 4covers the passenger rear corner too (layout A)
Seat foam A2, rear to the driver sideHR foam157 7/8 x 20 x 4covers the driver rear corner
Seat foam A3, driver innerHR foam127 1/2 x 22 5/8 x 4its own cushion: the dog food lid opens daily
Backrest, passengerfoam156 1/4 x 14 x 2 1/2ASSUMED size; lifts off
Backrest, rear (two halves)foam240 1/8 x 14 x 2 1/2ASSUMED
Backrest, driverfoam144 5/8 x 14 x 2 1/2ASSUMED
Non-slip padrug gripper3each seat footprint, 1/2 in inunder the cover bottoms

Order and measuresteps 1 to 3

    1. Home Depot #4013: one more 2-pack of the 3 in matte black hinges (six needed, four in hand), felt pads, 25 ft of 1/2 in split loom.
    2. Hold the stays and latches until a lid is weighed and measured (step 2). Hold foam and fabric until the sit test (step 3).
    3. Lighting (the lip strip, the button) and the two Sirocco fans wait on the full lighting map. Don't buy them twice: the bed guide lists the same strip and button.
    Tip Everything in the 'Have it' group is already in the truck or the shop. Count the poplar before the next Mr Plywood run.
    1. Both lounge window openings: width, height, and the sill above the bench box top (taped once at 19 1/4 to the window). The rail frames are cut from these, never from this page.
    2. Lid thickness and weight, with a cushion-sized load on it. That picks the stay and the latch.
    3. Bed down: lower it fully and tape the strut bottom above the floor. This page derives 28 3/4 from the window sill; the Happijac rail hangs about 2 lower.
    4. The aft Happijac columns: where they stand and how they meet the rear bench. The page puts them in the rear corners on the bench top, ASSUMED.
    5. The fridge: body plus slide height against 19 3/4 under the lid, and the fridge's full travel forward (measure sheet B14).
    Caution Every bench number is to the walls from outside with the lids off (Jeff, 09-09). Re-tape any number you cut a lid or panel to.
    1. The box top is 20 1/2 with the lid; 4 in of foam puts the seat at 24 1/2. A chair is 17 to 19. Sit on the lid with a 3 in and a 4 in scrap of foam and decide.
    2. Lower the bed onto the foam scrap: with 4 in of foam there is about 2 1/4 between the cushion and the Happijac rail at the walls, more in the middle under the struts.
    3. Try the table on its post at seat height plus 9 to 11 in, and check it has to come out (or drop) before the bed comes down.
    4. Try a backrest pad: a folded blanket 2 1/2 thick against the wall panel. It shortens the 22 5/8 seat to about 20, which is where it wants to be.
    Tope The benches are high because the water bay needs 20 in clear under the lid. Thinner foam is the only lever left on seat height; a footrest under the table is the other.

Bench boxessteps 4 to 12

    1. The boxes stand already. Check each one is held, not just placed: a 364 lb wet tank and a full fridge sit beside them.
    2. Floor cleats, 3/4 x 1 1/2, inside each front: screws sideways into the front, and down into the 1/2 ply only (#8 x 3/4 at most: the XPS is under it).
    3. Wall ledgers, 3/4 x 3, along each wall under the box top: into the 8020 with T-nuts or into the wall ply, never through the skin.
    4. Ends and dividers screwed through to the fronts. Nothing rocks when you push a corner hard.
    Caution No screw through the floor: under the 1/2 ply is 1 in XPS and the original deck, and somewhere under the rear bench is the Buyers box.
    1. A fixed 3/4 ply strip, 3 wide, along each wall on top of the ledger, flush with the lid tops at 20 1/2.
    2. It does three jobs: the lids hinge on its front edge, the wall panel stands on its back edge (the bench bearing, TP19), and the lid opens without scraping the panel.
    3. Rear strip runs the full 80 1/2 including both corners; the side strips stop at the rear strip.
    Tip If the lids already run to the wall, rip 3 in off their back edge and screw that down as the strip: same thing, no new wood.
    1. The CFX3 rides out forward on its slide through the drawer face; it never comes out through the top. So the lid over it is fixed (Jeff's list: secure fridge lid).
    2. Screw the fridge lid down to the front, the strip and the rear front with four #8 x 1 1/4 in cup washers, so it can come off for service.
    3. Before it goes down: the fridge body plus slide has to clear 19 3/4 under the lid. Drawn with a 3/4 slide, it clears by about 5/16: ASSUMED.
    4. Run the fridge fully out: nothing may be mounted or wired in that travel, and the floor plan shows it touching the forward column. Look at the column.
    Caution A fridge lid that can lift is a fridge lid that lands on someone. Screw it.
    1. Two lids: lid 1 over the core pocket (Isotemp on edge, pump group), lid 2 over the tank. The joint lands on a crossrail at about 34 3/4 from the passenger wall.
    2. Crossrail 3/4 x 1 1/2 on edge, from the rear front to the strip, screwed through the front and into the ledger.
    3. Lid 1 opens most (service). Lid 2 opens for the tank ports and the level sender, which are at one end of the tank: check which end before choosing hinge side.
    4. The plumbing guide installs everything in the bay. This step only keeps the lids out of its way.
    Tip Clear height under the lid was taped 20 (07-27) and 18 1/2 (09-09). Re-tape it to the lid underside once the strip is in: the open question on STATUS.
    1. Opened every day, so it gets its own lid, its own cushion and a stay that holds it.
    2. The bin: an airtight 33 qt stands under the lid if it is under 19 in tall. Measure before buying.
    3. Leave the back 1 1/2 in along the wall clear for the bed light cable (step 17).
    4. The Eberspacher was planned 'under a bench seat', which bench never recorded. If it is this one, it changes the bin and the cable route: decide now.
    1. Jeff's list: trim lounge lids. Cut each lid so it sits with a 1/16 gap to the strip and its neighbours, and the 1/8 lip over the front.
    2. Sizes as drawn: fridge 39 5/16 x 19 11/16, dog food 27 13/16 x 19 11/16, rear 33 and 47 3/8 long x 16 9/16. Fit to the real box, not these.
    3. Ease every edge with a block. Band raw ply edges (iron-on) or leave them if they are white melamine.
    4. A finger notch or the latch knob at each opening lid's front edge, centred.
    Tip Lay them all down together and look along the gaps from the open middle before cutting the next one.
    1. Two 3 in matte black utility hinges per opening lid: dog food, rear 1, rear 2. Six total.
    2. Surface-mount on top, knuckle on the joint between strip and lid, about 4 to 5 in in from each end. The cushion hides them.
    3. #8 x 5/8 into 3/4 ply (a 3/4 screw comes through). Pilot every hole.
    4. Open and shut each one ten times. A lid that binds on the strip: plane its back edge, not the strip.
    Caution Hinge screws into ply end grain pull out. Every screw goes into the face of the strip or the lid.
    1. One soft-close stay per opening lid, on the box end or the front inside, so a lid stays open while both hands are in the bay.
    2. Weigh the lid with its cushion first: the Numhew is 3 to 10 lb each. The 47 in tank lid may want one each end.
    3. Mount it with the lid at the angle you want (about 80 degrees: the lid leans back on the wall panel otherwise and marks it).
    1. A Southco M1-2A pop-out knob in the front edge of each opening lid, catching on the front panel's inside. Push to latch, pop to open.
    2. Felt pads where each lid lands: front, crossrail, ends. They stop the drumming.
    3. The fridge lid is screwed, so it needs neither.
    Tip Before drilling the latch hole, check the M1-2A's thickness range against your lid: listed 1/2 to 3/4.

Windows and wallssteps 13 to 16

    1. The kitchen system: a 2 x 1 1/2 poplar rail frame around each window, laminated from two 3/4 layers with staggered half-lap corners, on L brackets to the 8020.
    2. The page draws a 34 x 20 opening (photo estimate) and a 38 x 24 frame. Build to the measured opening.
    3. The frame face is the magnet annulus: the panel beds flush on it. Groove for the keeper steel as the kitchen frame did.
    4. Both frames take about 41 ft of 2 in strip. Count the rail stock before the glue-up.
    Caution The window's own leak path was the outside sill (water pooled and wicked in). Sikaflex fillet first, frame second.
    1. The 09-28 video shows panels up. Check each against this: bearing on the back strip below, a whisker off the Happijac steel, black trim lapping the top, magnets holding it flat.
    2. Passenger panel 59 5/8 long (the taped 59 plus the 5/8 drawer face), driver panel 47 3/8 (the taped 47 3/8). Both up to 63 7/8, level with the kitchen panel top: ASSUMED.
    3. Window cutout from a cardboard template off the real frame, laps the frame opening by about 1/2, corners radiused, as the kitchen panel.
    4. No face screws. LED never mounts to a removable panel.
    Tip Template first, numbers into the notebook, then cut. Same discipline as the kitchen panel.
    1. Three pieces of 1/2 birch with two 3/8 shadow gaps (black U-channel), standing on the rear strip. Up in the 09-28 video.
    2. Check: the channels' legs sit just under the panel face, the gaps are plumb, nothing rattles with a fist.
    3. The bed's back board comes within about 1 in of this wall at full travel: nothing on it may stand proud.
    1. At each forward column: the 1/2 x 1/2 black anodised angle, on black VHB to the steel side only, lapping the panel edge (E4).
    2. Panel tops: black top trim lapping them, fixed to the steel or the 8020, never to the panel (E1).
    3. Black anodised everywhere. Matte black beside it will not match.

Power and airsteps 17 to 19

    1. The bed lights' cable comes down the 1 1/2 in slot between the driver-side back column and the wall (bed guide).
    2. Into the rear bench through a grommeted hole in its back, along the driver wall inside the rear and dog food benches in split loom, clipped every 12 in.
    3. From the dog food bench's forward end, about 12 in of open wall to the forward column, then up to the control box in the upper cabinet. That last run is behind a panel: route not decided.
    4. Leave a pull string beside it.
    Caution Keep it clear of the bin, the lid stays and the hinge screws, and out of the bed's travel band at the column.
    1. The lighting plan's fourth zone: an RGB + warm strip under a fixed oak lip on the rear bench front, washing the bench face and floor (E10).
    2. White oak 3/4 x 1 1/2, 35 1/4 long across the open middle, screwed to the top of the rear front, standing 3/4 proud. Channel in its underside.
    3. On the carcass, never on a lid: LED never mounts to anything that moves.
    4. Rough the wire in now, through the front near the passenger end. Strip and controller wait on the lighting map.
    1. Two Caframo Sirocco II blowing into the lounge. Drawn on the bed deck underside, 3 in behind the front board, over the open middle: ASSUMED.
    2. Over the open middle, because they hang about 4 1/2 below the deck: over the benches they would hit the cushions with the bed down.
    3. On the deck their power rides the bed's drag chain (2 more cores, the bed guide's 9+ core cable). On a wall or a column instead: hard-wired, no chain, but they aim at the room only with the bed up.
    4. Jeff's call before the chain cable is bought.

Cushions and tablesteps 20 to 23

    1. Layout A (chosen 09-09): A1 runs the whole passenger side including its rear corner; A2 runs the rear from there across, taking the driver corner; A3 is the driver inner.
    2. A1 59 x 22 5/8, A2 57 7/8 x 20, A3 27 1/2 x 22 5/8, at the thickness from the sit test.
    3. HR foam, medium-firm for seats you also sleep under. IN-EX cuts it to the list; take this page.
    4. Wrap each in 1/2 in Dacron.
    Tip A1 is over the fridge and the core pocket, both serviced rather than opened; A3 is alone because the dog food lid opens every day.
    1. Box covers with a zip along the back face, so the foam comes out and the cover goes in a wash.
    2. Non-slip pad sewn or stuck to the cover bottom, not loose on the lid.
    3. Fabric is Jeff's pick: tough, washable, dog-proof. Mill End Store for a feel of it; a local upholsterer if not sewing it.
    4. Make A1 first and live with it a week before cutting the other two.
    1. Four lift-off pads, 2 1/2 thick and 14 tall, on the three walls between the seat and the window sill: ASSUMED.
    2. They stand on the seat and lean on the wall. If they need holding, two hooks into the back strip, never into a panel: the panels are removable and take no load.
    3. They come off before the bed lowers: the Happijac rails come down to about 26 3/4 at the walls. Laid flat on the seat cushions they fit under the bed's middle.
    4. Skip them entirely if the sit test says the wall panels are fine to lean on.
    Caution Nothing that hangs on a wall panel. The panels are held by geometry, and a backrest load will pull one off its magnets.
    1. The table is in the truck on its post. Check its floor socket is through-bolted to real structure, not screwed into the 1/2 ply.
    2. Top drawn 24 x 30 at 34: ASSUMED. It fits the 35 3/8 open middle with room for knees.
    3. It comes out, or drops below the bed, before the bed lowers. Give the top and the post a home: in the dog food bench or under the bed.
    4. Travel: post out and stowed, or locked so it cannot swing.

Checksteps 24 to 25

    1. Lids latched, fridge lid screwed, table stowed, backrests down.
    2. Drive a washboard road. Listen for lids drumming, cushions walking, the fridge slide clunking.
    3. Re-tighten every hinge screw after the first week.
    1. Table out, backrests off. Lower the bed slowly and watch every edge: cushions, latches, the fans, the bench lip, the column slot cable.
    2. Tape the strut bottom and the rail bottom above the floor. This page assumes 28 3/4 and 26 3/4: correct it here and on the bed page.
    3. The window sill should sit 2 to 2 1/2 above the bare mattress at the head end, as taped 09-30.
    4. Raise it again and check nothing came up with it.
    Caution The drive shaft spins as the bed moves: nothing in the lounge may reach it.
Notes10
  • Sources: bench runs and depths are Jeff's tape, 2026-09-09 (Lounge cushions); where the benches sit is the floor plan's chain; heights from the 3D interior; the bed is Bed build, as built 2026-09-30.
  • Frame on this page: x aft of the cab wall, y across from the PASSENGER wall (the floor plan's Y from the driver wall is 84 minus this y), z up from the floor. Mirrored so the drawing looks at the fridge bench and the passenger window.
  • ASSUMED, measure before relying on it: the lounge window openings (34 x 20 from a photo), the lounge walls centred in the box (1 3/4 each side), 3/4 ply carcass and lids, the 3 back strip, the panel top at 63 7/8, 1/4 panels, the aft Happijac columns in the rear corners, foam at 4, backrests 2 1/2 x 14, the table 24 x 30 at 34, the fridge size and slide, the fan position.
  • Bed down is DERIVED, not taped: window sill 39 (box top 19 3/4 plus the taped 19 1/4) less 2 1/4 (Jeff, 09-30) less the 6 in mattress and the 2 in strut and deck gives 28 3/4 to the strut bottom. The 3D interior page instead puts the platform ON the bench tops at 20 1/2; that would crush the cushions and contradicts the sill measurement. Step 25 tapes it.
  • Seat height: 24 1/2 with 4 in foam, 5 to 7 in above a chair. Forced by the 20 in clear the water bay needs. Settle the foam by sitting on it, not from this page.
  • Cushion layout A, chosen 2026-09-09: the dog food lid opens daily so it has its own cushion; the fridge and water bay are serviced, so long cushions over them cost nothing.
  • Panels: held by geometry (bearing below, trim lapping above, magnets only to keep them flat). Nothing hangs on them, LED never mounts to them. Walls and windows, edge details E1, E2, E4, E10 and TP18 to TP20.
  • Lighting: the rear bench lip is the lighting plan's ready-made fourth zone. It, the bed lights and the fans go into the full lighting map before any controller is bought. Interior lighting.
  • Rail stock conflict: the 08-10 log says the 20 ft buy is not enough for both lounge frames (about 46 ft of strip needed), but the 08-06 note says the first 40 ft covers the kitchen and both lounge windows. Count the strip in hand before the glue-up.
  • Not on this page: the bed (bed-build), the water bay plumbing (plumbing guide), the fridge's electrics, the Eberspacher (bench never recorded).