Shower
wedi floor and walls, the swing door to the kitchen, the slider to the cab, microcement.
Every part and material the shower uses, written down once. The build steps point here. Mark things Ordered or I have it as they happen; it syncs with Done.
PartStatusNeedWhereUsed in
wedi Fundo Primo base, 36 x 72, center drain, US9100006trims to about 52 1/4 x 19 5/16 (a); edge 1 37/64 (s); drain 20 from the driver 80/20 (m, checked clear below)
due Oct 21
1
Portland Direct Tile (call 503-230-9500), else Master Wholesale $732.52 at Portland Direct Tile & Marble, in stock (Nathan, 2026-10-13)
Click and Seal 2 in drain (with the base)floor hole about 1/2 in over the drain body (plan 5 in) (s); 2 in Sch 40 stands up inside the body, height from the drain sheet (s)
1
comes with the base
Driver-side box over the PEX: two 1/2 ply walls and a 1/2 ply top, the lower wall stands on itSame height as the cab box, 3 1/4 raw (Jeff, 2026-10-21); the front wall's face on the rib line, 3 3/8 from the 80/20
1/2 ply offcuts
D1 curb, white oak core under 1/4 wedi, site-builtcore 20 3/4 x 3 1/4 x 1 1/2, finished 3 1/2 high (Jeff, 2026-10-21); D2 sits on the cable box
1
white oak 1x6 and wedi offcuts
wedi PRO-SET modified thinset, 25 lb3/16 to 5/16 compressed under the base (s)
1
2 in Sch 40 PVC, 2 x 1 1/2 reducer, primer and cementroute checked clear underneath (m)
Home Depot #4013 ~$21
Upper band skin, 1/4 Baltic birchno cab wall overlay any more (Jeff, 2026-10-12): the wedi goes on the factory plywood, pocketed on its back over each bolt head
a strip 52 1/4 x 7 1/4
1/4 Baltic birch on hand
Upper band ribs, 3/4 plywood, scribed5/8 step back (a)
from the 18 mm sheet
Cable box and D2 curb, the whole cab wall: 2x4 blocks, a 1/2 ply top, wedi on its face and topframe 3 high, 2 out; 3 1/2 x 2 1/2 finished; bundle depth off the cab ply still to measure (2 1/2 assumed)
2x4 and ply offcuts
Driver wall above the shelf: two corner cleats and a batten, poplar 2x2 ripped to 1 x 1 1/2in the 80/20's plane between the shelf and the 68 bar: the wedi screws to it (Jeff, 2026-10-12: no okoume skin)
one 2x2, 8 ft (shared with D1)
Lower driver wall: 1/2 ply ribs and shelf plate, 4 in out4 in out from the 80/20 to a shelf about 48 up (Jeff, 2026-10-12)
four ribs and a plate, 3 3/8 wide
1/2 ply on hand (Jeff, 2026-10-21)
Fixture blocks, 3/4 okoume
18 mm 4 x 8 (shared)
wedi building panel 1/4 in, 48 x 60 (US8000013)about 66 sq ft of pieces on 5 boards; the fifth is mostly spare (Jeff, 2026-10-13: all 1/4)
5
Portland Direct Tile & Marble (call 503-230-9500) $73.93 ea at Portland Direct Tile & Marble, stock to confirm (Nathan, 2026-10-13)
wedi building panel 1/2 in, 3 x 5: the six in the kitarrives with the base about Oct 21; the all-1/4 plan does not use them
6
in the wedi kit (Home Depot)
no step yet
Ply backing under the wedi, 6 mm okoume BS-1088, 4 x 8the driver wall, above and below the shelf, and the cable box face, about 12 sq ft (Jeff, 2026-10-13)
1
Crosscut Hardwoods about $90 to $150
Modified thinset for the boards, 25 lb (ANSI A118.15)the boards bond full-face, 1/4 square notch
2
Tile This (wedi PRO-SET) $19.55 ea
#8 x 3/4 stainless screws (cab wall, partition, wardrobe: nothing may come through)
1 box
Home Depot #4013 ~$10
wedi tabless washers, 100not needed: the fastener kit's 100 washers are loose and go with the 3/4 screws too
no step yet
Cab bolt access: printed sleeve and O-ring cap for each box-to-cab boltsleeve fits a socket over the head and ends flush with the wedi; cap flush with the microcement; a flexible sealant line at the microcement edge
one per bolt (count them)
P1S at Mark's (PETG; ASA if warm) + stock O-rings
Microcement: CimentART Aqua shower systemmesh, Primer, 2 x Aqua Base, Aqua microcement, sealer, 2 x two-part varnish (s)
about 91 sq ft
Ceiling profile ribs and battensflat 76 1/4 for 12 in, curve to 70 1/2 at the cab (m)
2 + 5
Crosscut (ribs) + Home Depot (5 poplar 1x2 x 6 ft) ~$48 battens
Ceiling skins, 1/8 Baltic birch or 3 mm okoume, x2
1 sheet 4 x 8
Shower lights: two recessed 12 V pucks, wet-rated (IP67), white and redabout 2 1/2 to 3 in across, shallow enough for the ceiling cavity; in the flat part, 6 in from the partition, a third of the way in from each side; white and red on two QuinLED channels
2
VETUS FAN12 extract fan, 12 V, two speed5 1/8 face, 3 in cutout, 2 3/8 deep (s); 41 CFM rated, about 25 to 30 real; 33 dB, 0.145 A (s). Chosen over the Attwood blower and the MaxxFan Dome (Jeff, 2026-10-12)
1
VETUS SCIROCCO cowl, 316 stainlessabout 5 7/8 x 5, 2 proud (s); behind the Pelican box, 3 1/2 gap (m): keeps 1 1/2 clear
1
3 in PVC DWV sleeve and two blocking rings3 in hole saw; the second ring is a spare spot for a second fan, no hole. Fan centre ASSUMED 30 from the wardrobe, 66 1/2 up
1 ft
D1 air slots, routed through the door5/16 x 11, 3/4 apart, the lowest centred 7 in up: about 17 sq in open (the fan wants 12); edges sealed with epoxy before the finish (Jeff, 2026-10-12: slim slots, not round grilles)
5 slots
router, 5/16 straight bit, a straightedge jig
Fan control: off / low / high and a run-on timer
1
picked with the lighting plan
Black fan cover, printed: floating disc and ring5 3/8 across, 3 1/8 off the wall. Solid front sheds the handheld's spray (the FAN12 is sold not waterproof); air in through the shadow gap; grips the housing, no screws
1
P1S, black ASA
Laundry cubby side panel, 1/2 ply scribed to the ceiling20 3/8 long, scribed to the 8020 line: 4 1/8 tall at the front, closing on the ceiling curve to under 3/4 at the back
offcut
Laundry hamper flap with vent slots, hinged at the bottom, 1/2 Baltic birch30 5/8 x 3 3/16 (m); a row of 2 1/2 x 3/8 slots, routed or drilled and joined; drops down to load. Epoxy every edge and slot before the finish, like the D1 slots
1
1/2 Baltic birch on hand (Jeff, 2026-10-21)
Mesh hamper liner, a tray that pulls outsewn about 27 x 17 x 3, a sleeve along the front hem for the dowel
1 yd
1/2 in hardwood dowel, 36 incut to about 29 1/2: rides in the front hem
1
U-cradles for the liner dowel1 x 1 1/4 x 1 1/4, a 9/16 U on top; screwed to the wardrobe top at the front corners
2
P1S, PETG
Shower mixing valve (which one: not chosen)Jeff, 2026-10-12: a real mixing valve, not the Scandvik bridge or the volume control. Must fit about 3 3/8 of cavity and be serviceable; position ASSUMED 40 up
1
not chosen
PEX fittings to the valve: crimp or expansion, no push-fits
as the valve needs
D1 hinge upright, poplar 1 1/4 x 1 1/2, 7272 (s), at corner C: 1 1/4 into the opening, 1 1/2 deep, so the hinge leaf clears the wardrobe's wedi
a 2x2, 8 ft (or two 1x2 glued)
D1 strike jamb, poplar 1 1/4 x 1 1/2, notchedagainst the partition's edge; a 5/8 notch on its shower-side corner takes the door's lip and the gasket; the keeper screws into the full-depth part
2x2, 8 ft (with the upright)
D1 head, poplar 1 1/4 x 1 1/2, notchedabout 20 (a), top at 72
from the same 8 ft
D1 infill above the head, 1/2 plyabout 20 3/4 x 4 1/4 (a), top scribed to the ceiling
1
offcut
D1 apron, poplar 1x4, kitchen sideabout 20 (a), in front of the curb; no screw into the curb
1x4, 2 ft
D1 leaf, 12 mm Baltic birch19 1/2 wide (s) x the measured opening; opens to about 78 degrees
1
Mr Plywood 556076
D1 mirror, kitchen face: 1/8 safety-backed glass, frameless, polished edges14 x 56 (a): 1 in from the hinge edge, a 3 in band on the latch edge for the pull, bottom about 13 up; about 9 lb
1
a Portland glass shop, cut to size
TACO Marine 304 stainless piano hinge, 1 1/2 x 72, 0.037 (H14-0112A72-1)72 x 1 1/2 open, cut to the leaf; a screw in every hole: #6 x 3/4 into the oak upright, #6 x 3/8 into the 12 mm door (Jeff, 2026-10-12, over the 316 0.060: a 20 lb door, the latches hold it shut)
1
D1 catch lip, 1 x 1/8 black anodized aluminum bar on the door's shower facealong the strike edge and the top, 1/2 past the edge into the frame's notch: the catch on the door, so the kitchen face stays flush (Jeff, 2026-10-12; black aluminum, not poplar, 2026-10-21). Not magnetic: the cup magnets go in the notch, steel strikes on the bar
about 86 in
D1 latch, worked from both faces, and its keeperat 38 in: a body and bar on the shower face reaching over the lip to the keeper; a handle with a thumb lever on the kitchen face. Must open from inside the shower
1
to choose (thumb latch, or a marine slam latch with a handle each side)
D1 corner magnets: cup magnets and steel strikesflush in the lip's overhang near the top and bottom; strikes in the notch: they pull the corners in, hidden
2 + 2
D1 frame screws and glueupright into the wardrobe side and jamb into the partition's edge every 12 in; pocket screws down through the head; all glued
about 20
Home Depot #4013 (stainless or coated #8 x 1 1/4, PL or Titebond III)
D1 latch backing plate
1
SendCutSend
no step yet
Hinge drilling jig
1
P1S, PETG
no step yet
D1 open-stop bumper
1
P1S, TPU
no step yet
Door seals, EPDM bulb (D1 and D2)D1: in the frame's notch, squeezed by the door's lip to about 5/32; plus a sweep on the leaf's bottom
~25 ft
D2 fill strip behind the wardrobe, 1/2 ply1 3/4 x 39 1/8 (m): the cutout runs 1 3/4 behind the wardrobe face
1
offcut
D2 floor cleat, a 1 1/2 strip of 1/2 Baltic birch, plus temporary battensthe floor cleat on the shower side, inside the cab box; two scrap battens on the cab side while the glue and wedi cure, then off
1
1/2 birch offcuts
D2 infill, the doorway's driver edge, 1/2 ply5 7/8 x 39 1/8: post to the cutout's driver-side edge
with the D2 leaf
Husky PC100/200 hangers, clip stops, BG1 guide
1 pack
D2 leaf, 12 mm Baltic birch (the D1 sheet offcut), hardwood top rail20 3/4 wide (s): the 19 3/4 opening plus 1/2 laps; travel 20 1/2 (s)
D1 sheet offcut
D2 track cover, bent aluminium
1
SendCutSend
no step yet
D2 bracket bolts: 1/4-20 stainless, fender washers and nylocks on the cab side, sleeves through the wedithrough-bolted above the hole, washers and nylocks on the cab side (Jeff, 2026-10-12: just bolts, no tee nuts); drilled once the track is here
about 6
D2 track bracket: a bent stainless angle the track hangs from
1
SendCutSend (cut and bent), or Husky's face-fixing bracket
D2 parked keeper pad, 3/4 ply4 x 6, glued and screwed behind the cab ply from the cab side (Jeff, Oct 21: plan the lock early)
1
offcut