TopeLeave about Dec 1

Systems / Power and light / Control box

Control box

The upper-cabinet box: the face, the boards, every cable in, beside the air fryer.

8 TBD · 6 ready to order · 1 ordered · 2 have it · also: Lighting systemControl panel

Does it all fit: the face to scale, the two walls inside, the cables in, the space budget, the air fryer.

The idea

It fits, for control and lighting only. Face, two QuinLEDs, the fuse block, buses and 19 cables come to about 391 of 1820 cu in (21 percent), which leaves room to work and to add. Three conditions: the computers and network gear go to the electronics bay; the divider is a real heat shield and the air fryer is never run shut in; and the face is hinged with service loops so the deep box can be worked on.

The box is the left 10 in of the left upper cabinet, 13 tall, 14 deep to the 80/20 rails at its back. The air fryer takes the 12 in on its right, behind a divider. In the 3D: Open the face swings the panel open on its left hinge.

The face to scale

The control panel's layout (control-panel.html), now with the lighting rockers: MAIN (the bypass), LIGHTS A and LIGHTS B take the three old light-zone rockers' places. The scene rotary is gone: the door rockers and the remotes do scenes.

Ekrano GXA/C thermostatBlower knobEasyStart ProMAINLT ALT BPUMPINVSTARH2OCAMUSB-CUSB-CTo scale, 1 square = 1 in, 10 x 13. Hinge on the left. Hover a part.
on the facesizedepthnote
Ekrano GX7 3/8 x 4 7/84 3/167.4 x 4.9 face, 1.2 body plus about 3 for its plugs (Victron drawing)
A/C thermostat3 1/2 x 2 1/41 1/2Cruise N Comfort DT-05, about 3.5 x 2.25 (estimate until it arrives)
EasyStart Pro3 5/16 x 1 9/1613/1684.5 x 40 mm cutout, 1/2 deep, waits on the heater model
MAIN13/16 x 1 7/161 7/8ON-ON: ceiling pucks through QuinLED B, or straight on (lighting)
LIGHTS A13/16 x 1 7/161 7/8master for QuinLED A: the bed, garage, outdoor
LIGHTS B13/16 x 1 7/161 7/8master for QuinLED B: kitchen and shower
PUMP13/16 x 1 7/161 7/8the water pump's power, through the rocker
INV13/16 x 1 7/161 7/8signal to the inverter relay at the rear
STARLINK13/16 x 1 7/161 7/8signal to its relay at the rear
H2O13/16 x 1 7/161 7/8signal: the Isotemp element
CAM13/16 x 1 7/161 7/8signal: cameras and the PoE switch
USB-C1 1/8 x 7/81 5/8panel USB-C PD, about 1.5 behind
USB-C1 1/8 x 7/81 5/8panel USB-C PD

Inside two walls carry it all

The front 4 1/2 in is the face's own depth (the Ekrano needs 4 1/4). Behind it: the two QuinLEDs on a plate on the left wall, where a hand reaches from the open face; the fuse block, negative bus, + splits and signal strip on a back plate standing 4 in off the 80/20 (its face 10 in back, in reach), with the cables looping in the space behind it. Nothing on the divider.

LEFT WALL, from inside (face on the left)behind the face11 in reachQuinLED AQuinLED Blow entryBACK PLATE, 10 in back on standoffs (from the face)Fuse blockNegative bus bar+ splitsSignal terminal striptopTo scale. Grey bands: the 80/20 rails behind the plate (heights from the photo, measure). Hover a part.
insidesizewherewhat for
QuinLED A1 5/16 x 4 5/16 x 4 5/16left wall, highthe bed, garage, outdoor: 15 channels, terminals facing into the box
QuinLED B1 5/16 x 4 5/16 x 4 5/16left wall, lowthe kitchen and shower
Fuse block, 6 ATC, with negative bus5 7/8 x 1 5/8 x 3 7/8back plate, highBlue Sea 5045 or similar, about 5.9 x 3.9 x 1.6 (ASSUMED): the face's own loads
Negative bus bar, 12 way4 13/16 x 1 3/16 x 1 3/16back plate, middleboth lighting feeds' negatives, the MAIN bypass, the fuse block's return
Wago splits for the + slots2 3/16 x 13/16 x 5 3/8back plate, rightone 221-415 per fused + slot that feeds two runs
Signal terminal strip, 8 way4 x 7/8 x 1 3/16back plate, lowthe INV, STARLINK, H2O, CAM rockers to the 8-core signal cable to the rear relays

Cables in 19

Two entries, so the box is not a sieve: the ceiling runs drop in at the top back left (cables fill 15 percent of a 1 1/2 grommet), and the chase runs, feeds and signal cables come in low at the back left (27 percent of a 2 in). Diameters are estimates.

tagwhatcablemmentry
R1BED: the bed's junction box12-core continuous flex9.5Low entry
R2KCEIL: the kitchen ceiling pucks3-core6.5Top entry
R3TASK: the task pucks3-core6.5Low entry
R4UCAB: the under-cabinet strips5-core7.5Low entry
R5TOE: the toe-kick strips5-core7.5Low entry
R6SHWR: the shower pucks3-core6.5Top entry
R7GAR: the garage strips2-core7.0Low entry
R8OUT: the outdoor light3-core6.5Top entry
S1KEYPAD: the door switch6-core alarm cable5.0Top entry
P1FEED A: Lights A, 20 A12/2 tinned duplex8.5Low entry
P2FEED B: Lights B, 15 A14/2 tinned duplex7.5Low entry
P3BOX: the face's loads, 15 A12/2 tinned duplex8.5Low entry
P4PUMP in and out, 10 Atwo 14/27.5Low entry
P5PUMP out14/2 tinned duplex7.5Low entry
N1SIGNAL: 4 rockers to the rear relays8-core 22 AWG6.0Low entry
N2Ekrano: VE.CanRJ45 patch6.0Top entry
N3Ekrano: EthernetCat66.0Top entry
N4A/C thermostat cablethe ICEBOX's own5.0Low entry
N5EasyStart cableEberspacher's own5.0Low entry

Circuits power in, row by row

Four fused feeds come up from the WFCO: the pump's (through its rocker and out again), one per QuinLED (through its master rocker), and the box's own, which a 6-slot fuse block splits for the face. The A/C thermostat and the EasyStart take power over their own cables from the units they run, so they need no fuse here (check each one's harness when it arrives).

FROMFUSECABLETHROUGHTOWFCO 110 AP4, 14/2PUMP rockerthe water pump (P5 out)WFCO Lights A20 AP1, 12/2LIGHTS A rockerQuinLED A + inWFCO Lights B15 AP2, 14/2LIGHTS B rockerQuinLED B + inWFCO 1415 AP3, 12/2fuse block + studthe face's own loads, belowfuse block3 A18 AWGEkrano GXfuse block10 A14 AWGUSB-C PD ports, bothfuse block2 A20 AWGRocker lamps, all eightR2 ceiling pucks, white18 AWGMAIN rocker (ON-ON)up: QuinLED B ch 1 / down: negative bus4 signal rockers22 AWGsignal strip 1 to 4, common 5N1 to the relay board at the rearHover a row. The lighting channels' own landings are on the wire list below and on the lighting page.

The fuse block

slotfusefeedsAWGdraw, A (ASSUMED)
13 AEkrano GX180.5
210 AUSB-C PD ports, both148.0
32 ARocker lamps, all eight200.3
4spare0.0
5spare0.0
6spare0.0

Wire list 66 conductors

Every conductor that lands in the box, from and to, with its gauge, colour and the label for both ends. Build from this: tick each one off as it lands. The lighting rows come from the lighting page's channel table, so the two cannot drift apart.

Power 13

labelfromtoAWGcolour
PUMP+INP4, 14/2 + (from WFCO 1)PUMP rocker, line14red
PUMP+OUTPUMP rocker, loadP5 + (to the pump)14red
PUMP-P4, 14/2 -Wago, to P5 -14black
FEEDA+P1, 12/2 + (from WFCO Lights A)LIGHTS A rocker, line12red
QA+LIGHTS A rocker, loadQuinLED A + in (red, 7.62 mm)12red
FEEDA-P1, 12/2 -negative bus12black
QA-negative busQuinLED A - in (black, 7.62 mm)12black
FEEDB+P2, 14/2 + (from WFCO Lights B)LIGHTS B rocker, line14red
QB+LIGHTS B rocker, loadQuinLED B + in (red, 7.62 mm)14red
FEEDB-P2, 14/2 -negative bus14black
QB-negative busQuinLED B - in (black, 7.62 mm)14black
BOX+P3, 12/2 + (from WFCO 14)fuse block + stud12red
BOX-P3, 12/2 -fuse block negative bus12black

Face 9

labelfromtoAWGcolour
F1fuse block slot 1 (3 A)Ekrano GX +18red
F1-Ekrano GX -fuse block negative bus18black
F2fuse block slot 2 (10 A)USB-C PD ports, both +14red
F2-USB-C PD ports, both -fuse block negative bus14black
F3fuse block slot 3 (2 A)Rocker lamps, all eight +20red
F3-Rocker lamps, all eight -fuse block negative bus20black
MAIN-CMAIN rocker, commonR2 KCEIL white core18white
B1MAIN rocker, upQuinLED B channel 118white
MAIN-BYPMAIN rocker, downnegative bus18black

Signals 6

labelfromtoAWGcolour
INVINV rockersignal strip 122brown
STARLINKSTARLINK rockersignal strip 222orange
H2OH2O rockersignal strip 322violet
CAMCAM rockersignal strip 422grey
SIG-Cthe four signal rockers' other pins, daisy-chainedsignal strip 5 (common)22black
N1signal strip 1 to 5N1, the 8-core to the rear relays (3 spare)22as N1's cores

Door switch 5

labelfromtoAWGcolour
KEY1S1 KEYPAD core 1: rocker 1 up (MAIN on, brighter)QuinLED B button 122brown
KEY2S1 KEYPAD core 2: rocker 1 down (off, dimmer)QuinLED B button 222orange
KEY3S1 KEYPAD core 3: rocker 2 up (NIGHT)QuinLED B button 322violet
KEY4S1 KEYPAD core 4: rocker 2 down (OUT)QuinLED A button 122grey
KEY5S1 KEYPAD core 5: commonGND on both boards' button terminals22black

Lighting 33

labelfromtoAWGcolour
A1R1 BED warm coreQuinLED A channel 118yellow
A2R1 BED red coreQuinLED A channel 218red
A3R1 BED green coreQuinLED A channel 318green
A4R1 BED blue coreQuinLED A channel 418blue
A5R1 BED pucks white coreQuinLED A channel 518white
A6R1 BED pucks red coreQuinLED A channel 618red
A7R1 BED fan 1 coreQuinLED A channel 718blue
A8R1 BED fan 2 coreQuinLED A channel 818blue
A9R7 GAR warm coreQuinLED A channel 914yellow
A10R8 OUT white coreQuinLED A channel 1016white
B2R2 KCEIL red coreQuinLED B channel 218red
B3R3 TASK white coreQuinLED B channel 318white
B4R3 TASK red coreQuinLED B channel 418red
B5R4 UCAB warm coreQuinLED B channel 518yellow
B6R4 UCAB red coreQuinLED B channel 618red
B7R4 UCAB green coreQuinLED B channel 718green
B8R4 UCAB blue coreQuinLED B channel 818blue
B9R5 TOE warm coreQuinLED B channel 918yellow
B10R5 TOE red coreQuinLED B channel 1018red
B11R5 TOE green coreQuinLED B channel 1118green
B12R5 TOE blue coreQuinLED B channel 1218blue
B13R6 SHWR white coreQuinLED B channel 1318white
B14R6 SHWR red coreQuinLED B channel 1418red
R1+R1 BED + core 1QuinLED A group 1 + out, slot 118red
R1+R1 BED + core 2QuinLED A group 1 + out, slot 218red
R1+R1 BED + core 3QuinLED A group 2 + out, slot 118red
R7+R7 GAR + coreQuinLED A group 2 + out, slot 2 via a Wago (shared with R8)14red
R8+R8 OUT + coreQuinLED A group 2 + out, slot 2 via a Wago (shared with R7)16red
R2+R2 KCEIL + coreQuinLED B group 1 + out, slot 1 via a Wago (shared with R3)18red
R3+R3 TASK + coreQuinLED B group 1 + out, slot 1 via a Wago (shared with R2)18red
R4+R4 UCAB + coreQuinLED B group 1 + out, slot 218red
R5+R5 TOE + coreQuinLED B group 2 + out, slot 118red
R6+R6 SHWR + coreQuinLED B group 3 + out, slot 118red

The space budget

cu in
The box1820
Face devices and their depth207
Boards, fuse block, buses106
Backplanes49
Cables, 18 in of each, and the face loom30
In use391 (21 percent)

Rule of thumb: under 40 percent full stays workable. Volume is not the real limit here; reach and heat are.

Not in this box

thingwhy notwhere
Mac mini5 x 5 x 2, warm, wants airthe electronics bay (open on dc-circuits): the garage, under a bench, or the power bay
Router and PoE switchtwo boxes plus a dozen network cablesthe same bay: the cameras' cables end there, not here
ESP relay boardthe relays the signal rockers driveat the rear, beside what it switches, as the panel plan already has it
WFCO DC box and fusesthe 15 positionswhere it is; the box takes three fused feeds from it

If it gets tight later, the first thing to move is the two QuinLEDs: to a lighting box under the lounge's back seat (Jeff, 2026-10-12: a possible second space), leaving only signals and the face here. The bed, garage and outdoor runs are already nearer there; QuinLED A would go first.

The air fryer

An Our Place Wonder Oven is 11 1/2 wide, 10 5/8 deep, 11 5/8 tall: in a 12 bay it fits with 1/4 each side and about 1 1/2 above. Countertop ovens usually ask for around 4 in all round (check its manual), and it vents hot air. So: a divider with a heat shield and an air gap on its side; nothing of the box on the divider; and use it pulled out onto the counter, or with the cabinet door open, never shut in. The Test page has a heat test before the electronics go in.

Cut through

Show

What's in it 17 parts

The face

have it

Ekrano GX

have it
TBD

A/C thermostat

stock
TBD

EasyStart Pro

stock
TBD

Rockers x8, Carling Contura or Blue Sea, panel set

stock
TBD

USB-C PD ports x2

stock
TBD

The face panel: 1/4 aluminium or ply, side-hinged at the left

cut from stock

Inside

ordered

QuinLED A

stock
ready to order

QuinLED B

stock
ready to order

Fuse block, 6 ATC, with negative bus

stock
ready to order

Negative bus bar, 12 way

stock
ready to order

Wago splits for the + slots

stock
ready to order

Signal terminal strip, 8 way

stock
TBD

Backplanes: 1/4 ply on the left wall, and one on 4 in standoffs off the 80/20

cut from stock

Cables in

ready to order

Grommets: 1 1/2 top, 2 in low left

stock
TBD

Service loops and ties: 12 in at the face's hinge

cut from stock

Cabinet and air fryer

TBD

Divider: 1/2 ply with a heat shield on the air fryer's side

cut from stock
have it

Air fryer: Our Place Wonder Oven

have it
Tap a part, or a row on the left.