TopeLeave about Dec 1

Systems / Power and light / Control box

Control box

The upper-cabinet box: the face, the boards, every cable in, beside the air fryer.

8 TBD · 6 ready to order · 1 ordered · 2 have it · also: Lighting systemControl panel

The measurements to take, the questions, every part in order.

1 Measure 0 of 4 done

What the drawing still guesses. Type what you get; it goes to Claude with your other changes.

The box space

Inside: the cabinet's left side to where the divider goes, the floor to the top, the face to the 80/20 rails.

Sets: The face panel: 1/4 aluminium or ply, side-hinged at the left, Backplanes: 1/4 ply on the left wall, and one on 4 in standoffs off the 80/20

The 80/20 rails

Height of each horizontal rail's centre above the cabinet floor, and how far back from the face.

Sets: Backplanes: 1/4 ply on the left wall, and one on 4 in standoffs off the 80/20

QuinLED housing

When it arrives: its outside size and where its terminals face.

Sets: QuinLED A, QuinLED B

Air fryer clearance

Its manual's clearance to walls and above, and where it vents.

Sets: Divider: 1/2 ply with a heat shield on the air fryer's side, Air fryer: Our Place Wonder Oven

2 Settle

  1. The air fryer next to the electronics The Wonder Oven is 11 1/2 wide in a 12 bay: it fits with 1/4 each side, and countertop ovens usually ask for about 4 in all round. Running it shut in the cabinet will cook the divider. Plan: use it pulled forward onto the counter, or with the cabinet door open, and shield the divider either way.
  2. Computers and network The Mac mini, router and PoE switch do not fit with the rest and should not share heat with the air fryer: they go to the electronics bay. That bay is still open on dc-circuits.
  3. Thermostat and EasyStart power Both are planned as powered over their own cables from the A/C and the heater. If either wants 12 V of its own, it takes fuse block slot 4.
  4. The face's hinge Side-hinged at the left with catches (planned), or lift-off with screws. Hinged keeps every plug in when you open it.

3 Parts in build order

8 TBD6 ready to order1 ordered2 have it

Cabinet

TBDcut from stock

Divider: 1/2 ply with a heat shield on the air fryer's side

Buy and cut: ply + foil-faced ceramic or mineral board · qty 1

The air fryer is the hottest thing in the truck sitting next to the electronics: shield its side, keep an air gap.

Inside

orderedstock

QuinLED A

Buy: not picked yet · qty 1

1 5/16 x 4 5/16 x 4 5/16, left wall, high

the bed, garage, outdoor: 15 channels, terminals facing into the box

ready to orderstock

QuinLED B

Buy: not picked yet · qty 1

1 5/16 x 4 5/16 x 4 5/16, left wall, low

the kitchen and shower

ready to orderstock

Fuse block, 6 ATC, with negative bus

Buy: not picked yet · qty 1

5 7/8 x 1 5/8 x 3 7/8, back plate, high

Blue Sea 5045 or similar, about 5.9 x 3.9 x 1.6 (ASSUMED): the face's own loads

ready to orderstock

Negative bus bar, 12 way

Buy: not picked yet · qty 1

4 13/16 x 1 3/16 x 1 3/16, back plate, middle

both lighting feeds' negatives, the MAIN bypass, the fuse block's return

ready to orderstock

Wago splits for the + slots

Buy: not picked yet · qty 1

2 3/16 x 13/16 x 5 3/8, back plate, right

one 221-415 per fused + slot that feeds two runs

ready to orderstock

Signal terminal strip, 8 way

Buy: not picked yet · qty 1

4 x 7/8 x 1 3/16, back plate, low

the INV, STARLINK, H2O, CAM rockers to the 8-core signal cable to the rear relays

TBDcut from stock

Backplanes: 1/4 ply on the left wall, and one on 4 in standoffs off the 80/20

Buy and cut: offcut, four 4 in standoffs, T-nuts · qty 2

The back one stands 4 in off the rails: its face 10 in from the box's face, in reach, with the cables behind it. It comes off as one board.

Cables

ready to orderstock

Grommets: 1 1/2 top, 2 in low left

Buy: Home Depot #4013 · qty 2

The face

have ithave it

Ekrano GX

Have it: not picked yet · qty 1

7 3/8 x 4 7/8, 4 3/16 behind

7.4 x 4.9 face, 1.2 body plus about 3 for its plugs (Victron drawing)

TBDstock

A/C thermostat

Buy: not picked yet · qty 1

3 1/2 x 2 1/4, 1 1/2 behind

Cruise N Comfort DT-05, about 3.5 x 2.25 (estimate until it arrives)

TBDstock

EasyStart Pro

Buy: not picked yet · qty 1

3 5/16 x 1 9/16, 13/16 behind

84.5 x 40 mm cutout, 1/2 deep, waits on the heater model

TBDstock

Rockers x8, Carling Contura or Blue Sea, panel set

Buy: Blue Sea or Carling · qty 8

0.83 x 1.45 cutouts on 1.12 centres, 1.9 deep

MAIN (ON-ON), LIGHTS A, LIGHTS B, PUMP, INV, STARLINK, H2O, CAM. The scene rotary is gone: the door rockers and the remotes do scenes.

TBDstock

USB-C PD ports x2

Buy: not picked yet · qty 2

1 1/8 x 7/8, 1 5/8 behind

panel USB-C PD, about 1.5 behind

TBDcut from stock

The face panel: 1/4 aluminium or ply, side-hinged at the left

Buy and cut: cut to the layout · qty 1

10 x 13

Hinged on the cabinet's left side with two catches, so it swings open with every plug still in.

TBDcut from stock

Service loops and ties: 12 in at the face's hinge

Buy and cut: not picked yet

Other

have ithave it

Air fryer: Our Place Wonder Oven

Have it: Jeff's · qty 1

11 1/2 W x 10 5/8 D x 11 5/8 H in a 12 bay

Tap a card to find it here. Tap a part to find its card.