Systems / Power and light / Lighting
Lighting
Every light as one system: 24 channels on two QuinLEDs, the keypad and scenes.
Every light as a channel: the one-line, the channels, fixtures, runs, the control box, how it is controlled.
The idea
Every light in the truck is one system. The rule that organises it: every light is a channel. A channel is one dimmed wire on a QuinLED in the control box. The + side is shared everywhere; each channel switches only its own negative, which is what makes it a dimmer.
So the whole thing is four tables: the fixtures, the channels they land on, the runs that carry them home to the box, and the inputs that drive the channels (the door keypad, the bed button, the garage switch, the phone). 24 channels on two boards: QuinLED A has the bed and the back (10 of 15), QuinLED B has the kitchen and the shower (14 of 15). In the 3D every run is drawn from its fixture to the box, coloured by zone.
The one-line power, boards, channels, fixtures
Power comes up from the DC box on two fused feeds, one per board, each through a master rocker. Each board has fused + outputs, one per group of five channels; every fixture's + lands on one. Each channel goes out on its own core to its fixture. The inputs on the left tell the boards what to do; the MAIN rocker is the one switch that works with the boards dead.
Channels 24 of 30
| ch | what | run | controlled by |
|---|---|---|---|
| A1 | Bed strips, warm | R1 | bed button, phone, scenes |
| A2 | Bed strips, RGB red | R1 | bed button, scenes |
| A3 | Bed strips, RGB green | R1 | scenes |
| A4 | Bed strips, RGB blue | R1 | scenes |
| A5 | Bed underside pucks, white (the office) | R1 | bed button, phone |
| A6 | Bed underside pucks, red | R1 | scenes |
| A7 | Bed fan 1, driver front (on/off) | R1 | phone, bed button |
| A8 | Bed fan 2, passenger front (on/off) | R1 | phone, bed button |
| A9 | Garage strips | R7 | garage switch, phone |
| A10 | Outdoor light | R8 | door keypad OUT, phone |
| B1 | Kitchen ceiling pucks, white | R2 | door keypad MAIN, MAIN rocker (bypass) |
| B2 | Kitchen ceiling pucks, red | R2 | door keypad NIGHT, scenes |
| B3 | Task pucks, white | R3 | phone, scenes |
| B4 | Task pucks, red | R3 | scenes |
| B5 | Under-cabinet strip, warm | R4 | door keypad, scenes |
| B6 | Under-cabinet strip, RGB red | R4 | scenes |
| B7 | Under-cabinet strip, RGB green | R4 | scenes |
| B8 | Under-cabinet strip, RGB blue | R4 | scenes |
| B9 | Toe kick, warm | R5 | scenes |
| B10 | Toe kick, RGB red (the night light) | R5 | door keypad NIGHT, scenes |
| B11 | Toe kick, RGB green | R5 | scenes |
| B12 | Toe kick, RGB blue | R5 | scenes |
| B13 | Shower pucks, white | R6 | phone, scenes; a button by the shower later |
| B14 | Shower pucks, red | R6 | scenes |
Full on, everything at once: about 16 A on A (fuse 20 A, 12/2 feed) and 7 A on B (fuse 15 A, 14/2 feed). ASSUMED wattages: strips 10 W/m warm, 12 W/m RGB; pucks 3 W.
Fixtures
| fixture | count | colours | wires | run | where |
|---|---|---|---|---|---|
| Kitchen ceiling pucks | 4 | white, red | 3: + white red | R2 | the open floor, a row of four on the centre line |
| Task pucks under the uppers | 2 | white, red | 3: + white red | R3 | under the uppers over the counter, front edge |
| Under-cabinet strips, warm + RGB | 1 | warm, red, green, blue | 5: + warm R G B | R4 | under the uppers at the back, washing the wall |
| Toe-kick strips, warm + RGB | 1 | warm, red, green, blue | 5: + warm R G B | R5 | under the base cabinets at the floor |
| Shower pucks, IP67 (two: Jeff, 2026-10-12) | 2 | white, red | 3: + white red | R6 | the shower ceiling's flat part, 6 in from the partition |
| The bed: strips, pucks and both fans | 1 | warm, red, green, blue, pucks white, pucks red, fan 1, fan 2 | 12-core cable | R1 | round the bed and under it; its own junction box in the slot |
| Garage strips under the shelves | 1 | warm | 2: + warm | R7 | under the front edge of both garage shelves |
| Outdoor light (options below) | 1 | white | 3: + white, spare | R8 | outside: over the door, under the awning case or on the rack |
Runs home pull these before the walls close
Every run goes from its fixture to the control box in one piece, labelled at both ends with its tag. Lengths are from the 3D's paths plus 30 in of slack; tape them before you cut.
| run | tag | from | cable | carries | length |
|---|---|---|---|---|---|
| R1 | BED | the bed's junction box | 12-core continuous flex, 18 AWG | the bed: 8 channels and +12 | about 27 ft |
| R2 | KCEIL | the kitchen ceiling pucks | 3-core, 18 AWG | +, white, red to all four pucks, daisy-chained | about 12 ft |
| R3 | TASK | the task pucks | 3-core, 18 AWG | +, white, red to both task pucks | about 5 ft |
| R4 | UCAB | the under-cabinet strips | 5-core, 18 AWG | +, warm, R, G, B | about 6 ft |
| R5 | TOE | the toe-kick strips | 5-core, 18 AWG | +, warm, R, G, B | about 17 ft |
| R6 | SHWR | the shower pucks | 3-core, 18 AWG | +, white, red to both shower pucks | about 8 ft |
| R7 | GAR | the garage strips | 2-core, 14 AWG | +, warm | about 34 ft |
| R8 | OUT | the outdoor light | 3-core, 16 AWG | +, white, a spare for red | about 10 ft |
| S1 | KEYPAD | the door switch | 6-core alarm cable, 22 AWG | 4 button lines and a common to both boards' button terminals, one spare (signals, not power) | about 11 ft |
| P1 | FEED A | the DC box (WFCO), Lights A | 12/2 tinned duplex, 12 AWG | +12 V and negative for QuinLED A, 20 A fuse at the DC box | to the DC box (open) |
| P2 | FEED B | the DC box (WFCO), Lights B | 14/2 tinned duplex, 14 AWG | +12 V and negative for QuinLED B, 15 A fuse at the DC box | to the DC box (open) |
The control box
Front view of the backplane. The runs drop in at the top, each over the board it lands on; the feeds come up at the bottom. Hover a run to see its terminals light.
How it is controlled
| input | how | where | what it does |
|---|---|---|---|
| Door switch: two momentary rockers | wired, 6-core (S1) | by the entry door, the only switch in the cabin | Rocker 1, MAIN: tap up for the ceiling on, hold up to brighten; tap down for all off, hold down to dim. Rocker 2: up is NIGHT (red, low), down is OUT (the outdoor light). Up and down of rocker 1 and NIGHT go to QuinLED B's three button inputs, OUT to QuinLED A's. |
| Bed remote, WiZmote | wireless (ESP-NOW) | in a holder in the lounge | Bed lights on and off, brighter and dimmer, buttons 1 to 4 are scenes. WLED hears it directly: no WiFi, no hub. |
| Garage remote, WiZmote | wireless (ESP-NOW) | in a holder inside the barn door | The garage strips on and off, brighter and dimmer. Two AAAs. No cable to pull. |
| MAIN rocker, ON-ON | wired in the box | control box face | Up: the ceiling white goes through QuinLED B (dimmed, scenes). Down: the ceiling white's return straight to negative, full on, with no smart part alive. |
| Master rockers A and B | in each feed | control box face | Kills a whole controller: every light it drives off, without the app. |
| Phone and the Ekrano | WiFi | anywhere | Every channel, the scenes, schedules. WLED now, ESPHome or Home Assistant later: the same channels. |
Scenes
| scene | what is on | channels |
|---|---|---|
| WORK | bed up or down: ceiling white 100, task white 100, under-cabinet warm 60 | B1, B3, B5 |
| CHILL | under-cabinet warm 30, toe kick warm 20, bed strips warm 30, nothing overhead | B5, B9, A1 |
| NIGHT | toe kick red 5, everything else off: find the door without losing your eyes | B10 |
| SHOWER | shower white 100; NIGHT shower is shower red 20 | B13, B14 |
| PARTY | every RGB channel on a colour, the warm ones low or off | A2, A3, A4, B6, B7, B8, B10, B11, B12 |
| OFFICE | bed up: bed pucks white 100, ceiling white 50 | A5, B1 |
The scenes are from the design intent (lighting.html): light surfaces, not lines; chill and night first, party second.
Outdoor light options, pick the spot first
The spot decides the fixture: on the wall over the door, under the awning's case, or on the roof rack aimed down. Whichever, pull run R8 (3-core, so a red mode has a core) to the spot now. My pick: the warm strip under the awning case for evenings, plus a Caprera2 on the rack if you want a real flood.
| option | what | where and why | draw | channel | |
|---|---|---|---|---|---|
| Warm strip under the awning case | IP67 warm COB strip in an aluminium channel on the box wall, just under the F45s case, the length of the awning | A soft wash down the whole side: hanging-out light, matches the inside. No glare in your eyes. | about 1 A for 2 m | one channel (A10) | the pick for evenings |
| Lumitec Caprera2, black, white/red (101218) | Marine flood, IP67, 1000 lm white (5000K, CRI 70+) and a red mode, 4.9 x 1.7 x 2.8, bracket mount, US-built | On the roof rack or under the awning rail, aimed down at the door and steps: the find-the-steps and work light. Red keeps bugs and night eyes happy. | 1.3 A | A10 (its colour changes by power cycling: check its wiring before buying) | the pick for a proper flood |
| Optronics UCL41CB scene light | Low-profile sealed RV scene light, 1200 lm, 12/24 V, clear lens, flat to the wall | Flat on the box wall over the door: simple, bright, white only. | about 1 A | A10 | simple and cheap |
| Black RV porch light, white/amber (Safoner, WanDwel) | IP67 aluminium, about 1400 lm, white and amber, 3-wire | Over the door; amber for bugs. | about 1 A | A10 and A11 | cheapest |
Sources: Lumitec Caprera2, West Marine (white/red), Optronics UCL41CB, RV porch lights. Prices not checked.