TopeLeave about Dec 1

Systems / Water / Shower

Shower

wedi floor and walls, the swing door to the kitchen, the slider to the cab, microcement.

18 TBD · 42 ready to order · 9 ordered · 10 have it · update parts on your phone

Measure first, then every part in the order you build, each with where to get it and where it stands. Tap Mark or change on a part to tell Claude what's different.

1 Measure 8 of 14 done

These set sizes the drawing is guessing at. Type what you get in the box; it goes to Claude with your other changes. Bolt heads first: they decide which plywood to buy.

Cab wall bolt heads

Depth of the tallest head off the plywood face: calipers' depth rod, or a straightedge and a feeler.

Sets: Upper band skin, 1/4 Baltic birch

Room width at 3 heights

Driver 80/20 face to the wardrobe face: floor, about 36 in up, about 70 in up.

Sets: wedi Fundo Primo base, 36 x 72, center drain, US9100006, wedi building panel 1/2 in, 3 x 5: the six in the kit

Room depth at 3 heights

Cab plywood to the partition face, same heights.

Sets: wedi Fundo Primo base, 36 x 72, center drain, US9100006, D1 leaf, 12 mm Baltic birch

Floor diagonals

Corner to corner both ways; within 1/4 in of each other is square.

Sets: wedi Fundo Primo base, 36 x 72, center drain, US9100006

80/20 on the driver wall

Each upright and cross member, from the cab plywood and up from the floor; a straightedge across them.

Sets: Fixture blocks, 3/4 okoume, Driver wall above the shelf: two corner cleats and a batten, poplar 2x2 ripped to 1 x 1 1/2

The cab passthrough

Width, height, distance of its edge from the wardrobe face, bottom off the floor.

Sets: D2 infill, the doorway's driver edge, 1/2 ply, D2 track bracket: a bent stainless angle the track hangs from

Upper cab band

The shell's step back above the shelf, and a full-size cardboard tracing of the shell and the ceiling curve.

Sets: Upper band ribs, 3/4 plywood, scribed, Ceiling profile ribs and battens, Upper band skin, 1/4 Baltic birch

Ceiling heights

At the cab wall, 6 in out, 12 in out, the flat part.

Sets: Ceiling profile ribs and battens

The partition opening

Wardrobe face to the partition plywood's edge, and is the edge plumb.

Sets: D1 hinge upright, poplar 1 1/4 x 1 1/2, 72, D1 head, poplar 1 1/4 x 1 1/2, notched, D1 leaf, 12 mm Baltic birch

The fan zone

Centre from corner A and down from the ceiling; the wall thickness there; outside, the gap to the cargo box.

Sets: 3 in PVC DWV sleeve and two blocking rings, VETUS SCIROCCO cowl, 316 stainless

Wardrobe top and the cubby

Wardrobe top above the floor; the gap to the ceiling at the front, the middle and the back.

Sets: Laundry cubby side panel, 1/2 ply scribed to the ceiling, Laundry hamper flap with vent slots, hinged at the bottom, 1/2 Baltic birch

The vinyl

Thickness where it is cut or lifts.

Sets: wedi Fundo Primo base, 36 x 72, center drain, US9100006

Mark the drain

20 in from the driver 80/20, 12 1/2 from the cab plywood (the pilot hole): an X on the vinyl, photographed with the tape.

Sets: wedi Fundo Primo base, 36 x 72, center drain, US9100006

Where the shower goes

Stand in the room and mark the mixer height, the shelf top and the hook on the wall.

Sets: Shower mixing valve (which one: not chosen), Fixture blocks, 3/4 okoume

2 Parts in build order

18 TBD42 ready to order9 ordered10 have it

Already decided: The shower pan: wedi Fundo base, bought as parts; Wall waterproofing: wedi boards, all 1/4; 6 mm ply behind the driver wall and the box face; The finish: CimentART Aqua microcement; D1 hinge gauge: 0.060; Cab overlay thickness: 1/4 Baltic birch; Porthole: none for now. To change one, mark it on the part or tell Claude.

Under the floor · steps 27 to 28

the drain hole and the waste line, before anything goes on the floor

orderedstock

Click and Seal 2 in drain (with the base)

Buy: comes with the base · qty 1

floor hole about 1/2 in over the drain body (plan 5 in) (s); 2 in Sch 40 stands up inside the body, height from the drain sheet (s)

ready to orderstock

5 in hole saw and arbor

Buy: Home Depot #4013 · qty 1 + 1 · ~$75

ready to orderstock

2 in Sch 40 PVC, 2 x 1 1/2 reducer, primer and cement

Buy: Home Depot #4013 · ~$21

route checked clear underneath (m)

ready to orderstock

HepvO waterless valve, 1 1/2 in, 5717

Buy: hepvo.com · qty 1 · $35.20

Walls, framing and the fan opening · steps 7 to 26

the cab overlay, the curved band, the cable box, the driver wall, both door frames, the ceiling

have ithave it

D2 fill strip behind the wardrobe, 1/2 ply

Have it: offcut · qty 1

1 3/4 x 39 1/8 (m): the cutout runs 1 3/4 behind the wardrobe face

have ithave it

D2 floor cleat, a 1 1/2 strip of 1/2 Baltic birch, plus temporary battens

Have it: 1/2 birch offcuts · qty 1

the floor cleat on the shower side, inside the cab box; two scrap battens on the cab side while the glue and wedi cure, then off

ready to ordercut from stock

D2 infill, the doorway's driver edge, 1/2 ply

Buy and cut: Crosscut Hardwoods · qty with the D2 leaf

5 7/8 x 39 1/8: post to the cutout's driver-side edge

TBDSendCutSend

D2 track bracket: a bent stainless angle the track hangs from

Make: SendCutSend (cut and bent), or Husky's face-fixing bracket · qty 1

TBD until: the track's hole pattern; ask Woodward's for a face-fix bracket first

ready to ordercut from stock

D1 hinge upright, poplar 1 1/4 x 1 1/2, 72

Buy and cut: Home Depot #4013 · qty a 2x2, 8 ft (or two 1x2 glued)

72 (s), at corner C: 1 1/4 into the opening, 1 1/2 deep, so the hinge leaf clears the wardrobe's wedi

ready to orderstock

D1 frame screws and glue

Buy: Home Depot #4013 (stainless or coated #8 x 1 1/4, PL or Titebond III) · qty about 20

upright into the wardrobe side and jamb into the partition's edge every 12 in; pocket screws down through the head; all glued

ready to ordercut from stock

D1 strike jamb, poplar 1 1/4 x 1 1/2, notched

Buy and cut: Home Depot #4013 · qty 2x2, 8 ft (with the upright)

against the partition's edge; a 5/8 notch on its shower-side corner takes the door's lip and the gasket; the keeper screws into the full-depth part

ready to ordercut from stock

D1 head, poplar 1 1/4 x 1 1/2, notched

Buy and cut: Home Depot #4013 · qty from the same 8 ft

about 20 (a), top at 72

have ithave it

D1 infill above the head, 1/2 ply

Have it: offcut · qty 1

about 20 3/4 x 4 1/4 (a), top scribed to the ceiling

ready to ordercut from stock

D1 air slots, routed through the door

Buy and cut: router, 5/16 straight bit, a straightedge jig · qty 5 slots

5/16 x 11, 3/4 apart, the lowest centred 7 in up: about 17 sq in open (the fan wants 12); edges sealed with epoxy before the finish (Jeff, 2026-10-12: slim slots, not round grilles)

have ithave it

D1 leaf, 12 mm Baltic birch

Have it: Mr Plywood 556076 · qty 1

19 1/2 wide (s) x the measured opening; opens to about 78 degrees

ready to orderstock

D1 catch lip, 1 x 1/8 black anodized aluminum bar on the door's shower face

Buy: Wholesale Glass & Supplies (95 in) or OnlineMetals · qty about 86 in

along the strike edge and the top, 1/2 past the edge into the frame's notch: the catch on the door, so the kitchen face stays flush (Jeff, 2026-10-12; black aluminum, not poplar, 2026-10-21). Not magnetic: the cup magnets go in the notch, steel strikes on the bar

ready to orderstock

D1 corner magnets: cup magnets and steel strikes

Buy: Home Depot or Amazon (countersunk cup magnets, about 3/4 in) · qty 2 + 2

flush in the lip's overhang near the top and bottom; strikes in the notch: they pull the corners in, hidden

ready to orderhave it

D2 leaf, 12 mm Baltic birch (the D1 sheet offcut), hardwood top rail

Have it: D1 sheet offcut

20 3/4 wide (s): the 19 3/4 opening plus 1/2 laps; travel 20 1/2 (s)

ready to orderstock

Stainless #8 x 1 1/4 flat-head screws

Buy: Home Depot #4013 · qty 1 box

have ithave it

Upper band skin, 1/4 Baltic birch

Have it: 1/4 Baltic birch on hand · qty a strip 52 1/4 x 7 1/4

no cab wall overlay any more (Jeff, 2026-10-12): the wedi goes on the factory plywood, pocketed on its back over each bolt head

TBDcut from stock

Upper band ribs, 3/4 plywood, scribed

Buy and cut: Crosscut Hardwoods · qty from the 18 mm sheet

5/8 step back (a)

TBD until: trace the shell above the shelf

have ithave it

Driver-side box over the PEX: two 1/2 ply walls and a 1/2 ply top, the lower wall stands on it

Have it: 1/2 ply offcuts

Same height as the cab box, 3 1/4 raw (Jeff, 2026-10-21); the front wall's face on the rib line, 3 3/8 from the 80/20

ready to ordercut from stock

Driver wall above the shelf: two corner cleats and a batten, poplar 2x2 ripped to 1 x 1 1/2

Buy and cut: Home Depot #4013 · qty one 2x2, 8 ft (shared with D1)

in the 80/20's plane between the shelf and the 68 bar: the wedi screws to it (Jeff, 2026-10-12: no okoume skin)

have ithave it

Lower driver wall: 1/2 ply ribs and shelf plate, 4 in out

Have it: 1/2 ply on hand (Jeff, 2026-10-21) · qty four ribs and a plate, 3 3/8 wide

4 in out from the 80/20 to a shelf about 48 up (Jeff, 2026-10-12)

ready to ordercut from stock

Fixture blocks, 3/4 okoume

Buy and cut: Crosscut Hardwoods · qty 18 mm 4 x 8 (shared)

Before you order: the mixer in hand: its rough-in depth sets the mixer block

TBDprinted

Mixer drilling template

Print: P1S, PETG · qty 1

TBD until: the Scandvik in hand

have ithave it

Cable box and D2 curb, the whole cab wall: 2x4 blocks, a 1/2 ply top, wedi on its face and top

Have it: 2x4 and ply offcuts

frame 3 high, 2 out; 3 1/2 x 2 1/2 finished; bundle depth off the cab ply still to measure (2 1/2 assumed)

ready to orderstock

Smooth conduit, pull string, a spare empty conduit

Buy: Home Depot #4013

orderedstock

VETUS FAN12 extract fan, 12 V, two speed

Buy: Fisheries Supply (Seattle; ships) · qty 1 · $117.88

5 1/8 face, 3 in cutout, 2 3/8 deep (s); 41 CFM rated, about 25 to 30 real; 33 dB, 0.145 A (s). Chosen over the Attwood blower and the MaxxFan Dome (Jeff, 2026-10-12)

TBDstock

3 in PVC DWV sleeve and two blocking rings

Buy: Home Depot #4013 · qty 1 ft

3 in hole saw; the second ring is a spare spot for a second fan, no hole. Fan centre ASSUMED 30 from the wardrobe, 66 1/2 up

TBD until: the fan's spot behind the Pelican box

TBDcut from stock

Ceiling profile ribs and battens

Buy and cut: Crosscut (ribs) + Home Depot (5 poplar 1x2 x 6 ft) · qty 2 + 5 · ~$48 battens

flat 76 1/4 for 12 in, curve to 70 1/2 at the cab (m)

TBD until: trace the ceiling curve full size

ready to orderstock

Shower lights: two recessed 12 V pucks, wet-rated (IP67), white and red

Buy: a marine or RV supplier (search: IP67 12V recessed puck light white red) · qty 2

about 2 1/2 to 3 in across, shallow enough for the ceiling cavity; in the flat part, 6 in from the partition, a third of the way in from each side; white and red on two QuinLED channels

ready to orderstock

Ceiling skins, 1/8 Baltic birch or 3 mm okoume, x2

Buy: Mr Plywood (call 503-254-7387) or Edensaw · qty 1 sheet 4 x 8

ready to ordercut from stock

Laundry cubby side panel, 1/2 ply scribed to the ceiling

Buy and cut: Crosscut Hardwoods · qty offcut

20 3/8 long, scribed to the 8020 line: 4 1/8 tall at the front, closing on the ceiling curve to under 3/4 at the back

It carries the wardrobe wall's wedi up to the ceiling: the open strip above the wardrobe is part of the shower wall.

Before you order: trace the ceiling curve over the wardrobe

orderedstock

wedi building panel 1/2 in, 3 x 5: the six in the kit

Buy: in the wedi kit (Home Depot) · qty 6

arrives with the base about Oct 21; the all-1/4 plan does not use them

ready to orderstock

PEX fittings to the valve: crimp or expansion, no push-fits

Buy: Home Depot #4013 · qty as the valve needs

Before you order: the valve chosen

ready to orderstock

PEX pressure test gauge and caps

Buy: Home Depot #4013 · qty 1

have ithave it

D2 parked keeper pad, 3/4 ply

Have it: offcut · qty 1

4 x 6, glued and screwed behind the cab ply from the cab side (Jeff, Oct 21: plan the lock early)

Pan and wedi boards · steps 29 to 30

the base bedded and sloped, the boards on every wall, the flood test

orderedstock

wedi Fundo Primo base, 36 x 72, center drain, US9100006

Buy: Portland Direct Tile (call 503-230-9500), else Master Wholesale · qty 1 · $732.52 at Portland Direct Tile & Marble, in stock (Nathan, 2026-10-13)

trims to about 52 1/4 x 19 5/16 (a); edge 1 37/64 (s); drain 20 from the driver 80/20 (m, checked clear below)

The Click and Seal drain body comes with it.

ready to orderhave it

D1 curb, white oak core under 1/4 wedi, site-built

Have it: white oak 1x6 and wedi offcuts · qty 1

core 20 3/4 x 3 1/4 x 1 1/2, finished 3 1/2 high (Jeff, 2026-10-21); D2 sits on the cable box

ready to orderstock

wedi PRO-SET modified thinset, 25 lb

Buy: Tile This (or any A118.4 / A118.15 modified) · qty 1 · $19.55

3/16 to 5/16 compressed under the base (s)

ready to orderstock

Thinset trowels, mixing paddle, bucket

Buy: Home Depot #4013 · ~$35

orderedstock

wedi Joint Sealant, 10.5 oz

Buy: Floor & Decor · qty 7 · $21.06 ea

ready to ordercut from stock

D1 apron, poplar 1x4, kitchen side

Buy and cut: Home Depot #4013 · qty 1x4, 2 ft

about 20 (a), in front of the curb; no screw into the curb

ready to orderstock

wedi building panel 1/4 in, 48 x 60 (US8000013)

Buy: Portland Direct Tile & Marble (call 503-230-9500) · qty 5 · $73.93 ea at Portland Direct Tile & Marble, stock to confirm (Nathan, 2026-10-13)

about 66 sq ft of pieces on 5 boards; the fifth is mostly spare (Jeff, 2026-10-13: all 1/4)

Before you order: wedi's OK for 1/4 bonded on walls and ceiling over ply, and on the wardrobe melamine (wedi tech 847-357-9815)

ready to ordercut from stock

Ply backing under the wedi, 6 mm okoume BS-1088, 4 x 8

Buy and cut: Crosscut Hardwoods · qty 1 · about $90 to $150

the driver wall, above and below the shelf, and the cable box face, about 12 sq ft (Jeff, 2026-10-13)

ready to orderstock

Modified thinset for the boards, 25 lb (ANSI A118.15)

Buy: Tile This (wedi PRO-SET) · qty 2 · $19.55 ea

the boards bond full-face, 1/4 square notch

ready to orderstock

1/4 x 1/4 square-notch trowel

Buy: Home Depot #4013 · qty 1 · ~$12

ready to orderstock

#8 x 3/4 stainless screws (cab wall, partition, wardrobe: nothing may come through)

Buy: Home Depot #4013 · qty 1 box · ~$10

TBDstock

wedi tabless washers, 100

Buy: Amazon (wedi US5000009)

not needed: the fastener kit's 100 washers are loose and go with the 3/4 screws too

TBDprinted

Cab bolt access: printed sleeve and O-ring cap for each box-to-cab bolt

Print: P1S at Mark's (PETG; ASA if warm) + stock O-rings · qty one per bolt (count them)

sleeve fits a socket over the head and ends flush with the wedi; cap flush with the microcement; a flexible sealant line at the microcement edge

TBD until: the bolts: how many, head size, how proud, where; and a test pair

ready to orderstock

Construction adhesive for the ply backing (PL Premium)

Buy: Home Depot #4013 · qty 2 · ~$8 ea

orderedstock

wedi fastener kit, 100 screws + washers

Buy: Floor & Decor · qty 1 · $35.98

Finish, fan and shower · steps 32 to 34

microcement, then the fixture and the fan

orderedstock

Stainless drain cover, US1000057

Buy: Tile Tools · qty 1 · ~$74

flush with the finished floor

TBDstock

Microcement: CimentART Aqua shower system

Buy: CimentART USA · qty about 91 sq ft

mesh, Primer, 2 x Aqua Base, Aqua microcement, sealer, 2 x two-part varnish (s)

TBD until: ask CimentART: OK in a truck, and quantities

orderedstock

VETUS SCIROCCO cowl, 316 stainless

Buy: Fisheries Supply (Seattle; ships) · qty 1 · $73.13

about 5 7/8 x 5, 2 proud (s); behind the Pelican box, 3 1/2 gap (m): keeps 1 1/2 clear

TBDstock

Fan control: off / low / high and a run-on timer

Buy: picked with the lighting plan · qty 1

TBD until: the lighting controller decision

ready to orderprinted

Black fan cover, printed: floating disc and ring

Print: P1S, black ASA · qty 1

5 3/8 across, 3 1/8 off the wall. Solid front sheds the handheld's spray (the FAN12 is sold not waterproof); air in through the shadow gap; grips the housing, no screws

Before you order: the fan in hand (housing size ASSUMED 130 mm across, 60 mm off the wall)

TBDstock

Shower mixing valve (which one: not chosen)

Buy: not chosen · qty 1

Jeff, 2026-10-12: a real mixing valve, not the Scandvik bridge or the volume control. Must fit about 3 3/8 of cavity and be serviceable; position ASSUMED 40 up

have ithave it

Laundry hamper flap with vent slots, hinged at the bottom, 1/2 Baltic birch

Have it: 1/2 Baltic birch on hand (Jeff, 2026-10-21) · qty 1

30 5/8 x 3 3/16 (m); a row of 2 1/2 x 3/8 slots, routed or drilled and joined; drops down to load. Epoxy every edge and slot before the finish, like the D1 slots

ready to orderstock

Mesh hamper liner, a tray that pulls out

Buy: Amazon (search: polyester mesh fabric) · qty 1 yd

sewn about 27 x 17 x 3, a sleeve along the front hem for the dowel

Or a flat mesh laundry bag with the dowel through its open hem. Mesh, so the clothes breathe.

ready to orderstock

1/2 in hardwood dowel, 36 in

Buy: Home Depot #4013 · qty 1

cut to about 29 1/2: rides in the front hem

ready to orderprinted

U-cradles for the liner dowel

Print: P1S, PETG · qty 2

1 x 1 1/4 x 1 1/4, a 9/16 U on top; screwed to the wardrobe top at the front corners

The dowel drops in: the liner cannot slide back out of reach, and lifts out to empty.

ready to orderstock

Piano hinge, 30 in, for the flap

Buy: Home Depot #4013 · qty 1

Before you order: a spare from the lounge lid hinges, if there is one

ready to orderstock

Push-button travel latches for the flap

Buy: Amazon (the kitchen's latch) · qty 2

Same latch as every kitchen drawer: one part to stock spares for.

Doors · steps 36 to 38

both leaves made and hung

ready to orderstock

D1 mirror, kitchen face: 1/8 safety-backed glass, frameless, polished edges

Buy: a Portland glass shop, cut to size · qty 1

14 x 56 (a): 1 in from the hinge edge, a 3 in band on the latch edge for the pull, bottom about 13 up; about 9 lb

orderedstock

TACO Marine 304 stainless piano hinge, 1 1/2 x 72, 0.037 (H14-0112A72-1)

Buy: Fisheries Supply, Seattle, ships (SKU 41062) · qty 1 · $64.97

72 x 1 1/2 open, cut to the leaf; a screw in every hole: #6 x 3/4 into the oak upright, #6 x 3/8 into the 12 mm door (Jeff, 2026-10-12, over the 316 0.060: a 20 lb door, the latches hold it shut)

TBDstock

D1 latch, worked from both faces, and its keeper

Buy: to choose (thumb latch, or a marine slam latch with a handle each side) · qty 1

at 38 in: a body and bar on the shower face reaching over the lip to the keeper; a handle with a thumb lever on the kitchen face. Must open from inside the shower

TBD until: Jeff picks the latch type

TBDSendCutSend

D1 latch backing plate

Make: SendCutSend · qty 1

TBD until: the latch chosen

TBDprinted

Hinge drilling jig

Print: P1S, PETG · qty 1

TBD until: the hinge in hand

TBDprinted

D1 open-stop bumper

Print: P1S, TPU · qty 1

TBD until: the D1 mockup

TBDstock

Door seals, EPDM bulb (D1 and D2)

Buy: Amazon: Trim-Lok DD1604BT · qty ~25 ft

D1: in the frame's notch, squeezed by the door's lip to about 5/32; plus a sweep on the leaf's bottom

TBD until: sized at the mockups

ready to orderprinted

D2 flush pulls

Print: P1S, ASA (PETG to test) · qty 2

ready to orderstock

Husky PC100/200 hangers, clip stops, BG1 guide

Buy: Woodward's (call 888-915-5223) · qty 1 pack · $79.99

Before you order: Woodward's confirms it suits a 3/4 leaf with a 7/8 rail

ready to orderstock

Husky track, aluminium, 6 ft (cut to 41 1/2)

Buy: Woodward's · qty 1 · $69.99

section ASSUMED 1 1/8 x 1 3/16

Before you order: same call

TBDSendCutSend

D2 track cover, bent aluminium

Make: SendCutSend · qty 1

TBD until: the track in hand

ready to orderstock

D2 bracket bolts: 1/4-20 stainless, fender washers and nylocks on the cab side, sleeves through the wedi

Buy: McMaster-Carr or Fastenal · qty about 6

through-bolted above the hole, washers and nylocks on the cab side (Jeff, 2026-10-12: just bolts, no tee nuts); drilled once the track is here

TBDSendCutSend

D2 BG1 guide bracket

Make: SendCutSend · qty 1

TBD until: the BG1 in hand

TBDprinted

D2 travel latches, closed and parked

Print: P1S prototype, then ASA · qty 2

TBD until: the D2 bench mockup

Tap a card to find it here. Tap a part to find its card.