Systems / Power and light / Lighting
Lighting
Every light as one system: 24 channels on two QuinLEDs, the keypad and scenes.
7 TBD · 11 ready to order · 1 ordered · 1 built · 1 have it · also: Design intent (scenes)Control boxBed wiringControl panel
Pull every run first, then the box, the fixtures, land, program.
Build
Every step in order. Scroll and the drawing follows: it builds up to the step you are on and lights what that step adds.
Plan step 1
1
Settle the counts and spots
- Every fixture on the Overview's table: count, colours, spot. Change anything here first, then the runs follow.
- Answer the questions on the Plan page: the kitchen pucks' red, the garage switch, the toe kick, the shower count, the outdoor light.
Cables step 2
2
Pull every run before a wall or ceiling closes
- This is the step that cannot wait: every run on the cable table, from its fixture to the control box, while the walls are open.
- Label both ends before you cut: the run's tag (BED, KCEIL, TASK, UCAB, TOE, SHWR, GAR, OUT, KEYPAD) on a heat-shrink marker.
- 12 in of slack coiled at the fixture, 18 in at the box. Photograph each run in the wall with a tape in the shot.
- Pucks: a 3-core daisy chain, puck to puck, + to +, white to white, red to red, then one 3-core home.
- Strips: one 5-core home per zone (+, warm, R, G, B): the warm and RGB strips share the +.
- Outdoor: pull R8 to wherever the light will be even before the fixture is picked; a 3-core (spare core) if it might be white and red.
Caution Nothing behind a fixed panel without a label and a photo.
NeedsWaiting on 5 of 6
The bed: strips, pucks, fans, its junction box and 12-core cablebuilt3-core 18 AWG, tinned (pucks)ready to order5-core 18 AWG (strips: +, warm, R, G, B)ready to orderTinned cable: 14/2 to the garage, 16/3 outdoorready to order6-core 22 AWG alarm cable (the door switch)ready to orderWire labels and heat-shrink markersready to orderBox steps 3 to 6
3
The control box backplane
- QuinLED A and B side by side on the backplane, their channel terminals facing the top edge, where the runs come in.
- Feeds: 12/2 from the DC box's Lights A (20 A) and 14/2 from Lights B (15 A), each through its master rocker to its board's + in.
- Each run's + to its group's fused + output on the board (6.3 A a slot), split on a Wago where a slot serves two runs: the + table on the Overview says which slot. Negatives of the feeds on the box's negative bus.
- The MAIN rocker, ON-ON, in the kitchen ceiling's white return: common to the pucks' white core, one side to B1, the other to the negative bus.
Tip The control box drawing on the Overview shows every terminal.
NeedsWaiting on 6 of 6
QuinLED An-Penta-Deca A (bed and the back)orderedQuinLED An-Penta-Deca B (kitchen and shower)ready to orderControl box: the boards' + splits, negative bus, labelsTBDFuses at the DC box: Lights A 20 A, Lights B 15 ATBDRockers: master A, master B, MAIN (ON-ON bypass)TBDFeeds: 12/2 for A, 14/2 for B, tinned duplexready to orderFixtures steps 4 to 5
4
Pucks, the keypad, the outdoor light
- Each puck to its chain: + to +, white to white, red to red, Wago or crimp, strain-relieved behind the fixture.
- Door switch: rocker 1 up, rocker 1 down, rocker 2 up to B's button terminal (inputs 1 to 3), rocker 2 down to A's input 1, the common to GND on both, all on S1.
- Outdoor light through a sealed gland; silicone round it outside.
5
Strips in their channels
- The bed's recipe: warm and RGB side by side in aluminium channels, diffusers on, corners cut and jumped (no bends), the clip connectors from the bed.
- Each zone's leads to its 5-core: + to +, warm to warm, R, G, B.
Box step 6
6
Land every run on its channel
- Run by run, down the channel table: each colour core into its channel terminal, each + onto its board's bus.
- Label every terminal with its channel (A1, B5) and the run tag.
NeedsReady: everything is in hand
The bed: strips, pucks, fans, its junction box and 12-core cablebuiltProgram step 7
7
Name the channels and set the scenes
- WLED on each board: name every channel as the table names it. Fans (A7, A8) switch fully on, never dim.
- Scenes as the table: WORK, CHILL, NIGHT, SHOWER, PARTY, OFFICE.
- The door rockers in WLED's button settings: B's buttons 1 to 3 (MAIN up, MAIN down, NIGHT), A's button 1 (OUT): short press, long press, double press to presets.
- ESP-NOW on both boards; pair the two WiZmotes: the bed's to A1 to A6, the garage's to A9.
Commission step 8
8
Test it
- Every test on the Test page.