TopeLeave about Dec 1

Systems / Power and light / Lighting

Lighting

Every light as one system: 24 channels on two QuinLEDs, the keypad and scenes.

7 TBD · 11 ready to order · 1 ordered · 1 built · 1 have it · also: Design intent (scenes)Control boxBed wiringControl panel

The counts and spots to settle, the questions, every part in the order you build.

1 Measure 0 of 5 done

What the drawing still guesses. Type what you get; it goes to Claude with your other changes.

Control box

Where it is in the uppers and what is behind it: every run lands on its top or bottom edge.

Sets: Control box: the boards' + splits, negative bus, labels

The chase up the counter's aft end

A path from the floor to the uppers at the counter's aft end, beside the Happijac column: the bed, toe-kick and garage runs share it.

Sets: 5-core 18 AWG (strips: +, warm, R, G, B), Tinned cable: 14/2 to the garage, 16/3 outdoor

Door keypad spot

Inside, just aft of the entry door at switch height: what is behind the wall there.

Sets: Door switch: 2 momentary (ON)-OFF-(ON) rockers in a 2-gang plate

Outdoor light spot

Over the entry door outside: room under the awning, a way through the wall.

Sets: Outdoor light over the entry door, 12 V, IP65

Garage remote spot

Inside the barn door where you reach first: a holder for the WiZmote.

Sets: WiZmote remotes: garage and bed (ESP-NOW, WLED-native)

2 Settle

  1. Outdoor light Where it mounts sets what it is: see the options on the Overview (Outdoor light). Planned one channel, A10, on the door switch's OUT; a white/red fixture would take A11 as well.
  2. Door switch plate Two momentary rockers to match the control panel's, or four small push buttons. Either wires the same: four inputs and a common on S1.
  3. Toe kick Warm and RGB, like the under-cabinet, or RGB only (red is the night light; warm at the floor is a nice glow). Planned both; RGB only frees B9.

3 Parts in build order

7 TBD11 ready to order1 ordered1 built1 have it

Cables

builtcut from stock

The bed: strips, pucks, fans, its junction box and 12-core cable

Buy and cut: the bed plan · qty 1

Its own plan has every part. Here it is one run (R1) landing on A1 to A8.

ready to orderstock

3-core 18 AWG, tinned (pucks)

Buy: Amazon (search) · qty about 25 ft

runs R2, R3, R6

ready to orderstock

5-core 18 AWG (strips: +, warm, R, G, B)

Buy: Amazon (search) · qty about 23 ft

runs R4, R5

ready to orderstock

Tinned cable: 14/2 to the garage, 16/3 outdoor

Buy: Amazon (search) · qty about 44 ft

runs R7, R8

ready to orderstock

6-core 22 AWG alarm cable (the door switch)

Buy: Home Depot #4013 · qty about 11 ft

runs S1

ready to orderstock

Wire labels and heat-shrink markers

Buy: Amazon (search) · qty 1

Box

orderedstock

QuinLED An-Penta-Deca A (bed and the back)

Buy: DrZZs, order 93043 (2026-10-12) · qty 1 · $49 + $6.50 shipping

Channels A1 to A10: the bed's eight, the garage, the outdoor light; A11 to A15 spare. Ships with WLED.

ready to orderstock

QuinLED An-Penta-Deca B (kitchen and shower)

Buy: DrZZs · qty 1 · about $49

Channels B1 to B14: the kitchen and the shower; B15 spare. A second board because the truck needs 24 channels and one has 15.

TBDcut from stock

Control box: the boards' + splits, negative bus, labels

Buy and cut: Wago 221-415s + the box's negative bus · qty 1

Each board has three fused + outputs, one per group of five channels, two slots each at 6.3 A: a Wago on each slot splits it to its runs. The whole box: controlbox-overview.html.

TBDstock

Fuses at the DC box: Lights A 20 A, Lights B 15 A

Buy: the WFCO's own blade positions · qty 2

Two positions in place of the old ceiling / front / bed / outdoor four (dc-circuits.html): the QuinLEDs do the switching now.

TBDstock

Rockers: master A, master B, MAIN (ON-ON bypass)

Buy: the control panel's rocker set · qty 3

The panel rule: the van works with every smart part dead. MAIN down puts the ceiling pucks straight on.

ready to orderstock

Feeds: 12/2 for A, 14/2 for B, tinned duplex

Buy: Amazon (search)

Fixtures

have ithave it

Kitchen ceiling pucks, white and red, 3-wire

Have it: Jeff's · qty 4

The same pucks as the others (Jeff, 2026-10-12): + shared, white and red each on a channel. Touch each colour wire to 12 V and mark it before joining.

TBDstock

Task pucks under the uppers, white and red

Buy: Amazon (search) · qty 2

TBD until: the same model as the ceiling pucks, if it fits under the uppers

ready to orderstock

Shower pucks, IP67 12 V, white and red

Buy: marine or RV supplier · qty 2

The shower build's own record (shlights): leads placed in the ceiling before the skin goes on.

TBDstock

Outdoor light over the entry door, 12 V, IP65

Buy: a marine or RV supplier · qty 1

TBD until: which fixture

TBDstock

Door switch: 2 momentary (ON)-OFF-(ON) rockers in a 2-gang plate

Buy: Amazon (search) · qty 1

Each rocker is two buttons: up and down, springing back to the middle. The QuinLED's button terminal reads them directly: three debounced inputs per board, short to ground to press.

TBD until: the plate's look (match the control panel's rockers)

ready to orderstock

Under-cabinet strips: BTF FCOB warm 2700K + RGB, with channel

Buy: Amazon (search) · qty 1.4 m each

The same recipe as the bed: warm CRI 90+ beside RGB, one aluminium channel each, diffused.

ready to orderstock

Toe-kick strips: BTF FCOB warm 2700K + RGB, with channel

Buy: Amazon (search) · qty 1.4 m each

Red at a few percent is the night light: floor level, keeps night vision.

TBDstock

Garage strips under the shelves, warm

Buy: Amazon (search) · qty 4.0 m

Wet-ish space with the barn doors open: IP65 strip.

TBD until: what lives on the shelves (strip or pucks)

Program

ready to orderstock

WiZmote remotes: garage and bed (ESP-NOW, WLED-native)

Buy: Walmart or eBay (about $10 to $16) · qty 2

WLED hears a WiZmote directly over ESP-NOW (Settings, WiFi, ESP-NOW remotes: press a button, add its address). Replaces the Shelly BLU, which WLED cannot hear without ESPHome or a hub.

Tap a card to find it here. Tap a part to find its card.