TopeLeave about Dec 1

Systems / Living / The bed

The bed

The bed on the Happijac lift: frame, headboard, LEDs, pucks, the drag chain.

3 TBD · 20 ready to order · 2 ordered · 15 have it · also: Board shop drawingsBed manual (first build)Routing the channels

Tick what is done, check the channel, pick the cabinet; then every part in the order you build.

1 Measure 0 of 7 done

What the drawing still guesses. Type what you get; it goes to Claude with your other changes.

Bed down height

Floor to the underside of the Happijac rails, bed all the way down.

Sets: Continuous-flex cable, 12-core, 18 AWG, about 27 ft, Drag chain, 10 x 15 mm inside, about 4 ft

Bed travel

Underside of the rails, bed down and bed up.

Sets: Drag chain, 10 x 15 mm inside, about 4 ft, Continuous-flex cable, 12-core, 18 AWG, about 27 ft

The corner pocket

Behind the back Happijac column: from the rear wall to the column's back face (along the driver wall), and from the driver wall to the bed's edge. And anything in it: a rib, a bolt, the drive shaft's end.

Sets: Drag chain, 10 x 15 mm inside, about 4 ft

Control box spot

Which upper cabinet, and its distance forward from the bed's back edge along the driver wall.

Sets: Continuous-flex cable, 12-core, 18 AWG, about 27 ft, Control box, printed cover

The channel

Calipers: the channel's width and height.

Sets: Aluminium U channel, 16.93 mm wide, black, frosted diffuser, end caps, LED grooves, routed (if not already)

Drive shaft at full up

Bed all the way up: from the back strut's top to the underside of the drive shaft over the slot.

Sets: Back 1x5, the outer edge of the slot, Inner back wall, poplar 1x5 ripped to 3 1/2

Headboard clear of the window

With the bed down: from the head board's top to the window's bottom edge, and the window's fore-aft span.

Sets: Headboard panel, 1/2 in ply

2 Settle

  1. +12 V over a long run With the controller in the kitchen upper the cable is about 27 ft. Everything on full, the far end sees about 9.1 V from the 13 V bus on one 18 AWG +12 core: visibly dimmer and pinker. Planned: three of the twelve cores paralleled for +12 V, about 11.6 V at the bed, fine for 12 V strips. Or mount the controller near the bed and run only 14/2 power that far.
  2. Lid support brackets The lid supports' lower brackets go on the head board's inside face, in the 1/2 in above the mattress at each end, so they press a little into the mattress corners. If that bothers you, the other way is a folding stop: a short black strap from the headboard's back to the wall-side of the head board, which keeps it from falling forward and costs nothing.
  3. Holding it folded The old plan said magnetic catches, but folded the headboard lies on the mattress with nothing rigid under its free edge to catch. With the bed up the ceiling is only 1/2 above it, so it cannot move. Do you drive with the bed up? If so it needs nothing. If down, a strap or a weight on top (the bedding) is the simple answer.
  4. Veneer left? The headboard needs two pieces of the white oak veneer about 57 x 15 (both faces, so it stays flat). Is there that much left from the struts? If not, one more 2 x 8 sheet does it.

3 Parts in build order

3 TBD20 ready to order2 ordered15 have it

Frame

have ithave it

Struts, 6061 tube 1 1/2 x 3 x 1/8, lying flat

Have it: bought, dry fit 2026-10 · qty 4

78 3/8 long, the full frame width; white oak veneer on the bottom and sides (done)

Dry fit. For real: bolted to the Happijac's own black rails, one 1/4-20 per end, nut inside through an access hole the deck covers.

have ithave it

Strut bolts, 1/4-20 x 3/4

Have it: Home Depot #4013, bought 2026-09-30 · qty 8

Black steel with split washers is the interim set: swap to black stainless with nylocks when convenient.

have ithave it

Deck, 1/2 in ply, three sheets

Have it: bought, dry fit 2026-10 · qty 3

19 7/8 / 19 7/8 / 19 7/8 deep, 76 7/8 long, seams on the middle struts

The underside is the office ceiling: finished like furniture.

Boards

have ithave it

Head board, poplar 1x10 ripped to 8 1/2

Have it: Crosscut Hardwoods, bought 2026-09-30 · qty 1

60 3/4 long, 8 1/2 tall, on the driver rail

The only tall board: it carries the headboard. Shop drawing: bedlights-boards.html#head.

have ithave it

Foot board, poplar 1x5

Have it: Crosscut Hardwoods, bought 2026-09-30 · qty 1

60 3/4 long, 4 1/2 tall, on the passenger rail

Shop drawing: bedlights-boards.html#foot.

have ithave it

Front, 1x6 white oak ripped to 4 1/2

Have it: Crosscut Hardwoods, bought 2026-09-30 · qty 1

78 3/8 long, 4 1/2 tall, 1/2 in roundover on top

Screwed into the front strut, #10 x 1 1/4 and cup washers every 8 in. Oiled, not painted: the one piece of bare wood you see.

have ithave it

Back 1x5, the outer edge of the slot

Have it: Crosscut Hardwoods, bought 2026-09-30 · qty 1

78 3/8 long, 4 1/2 tall, on the rails flush with their ends; motor notch at the passenger end

The edge you see from below, and the back LED board: its two grooves face the rear wall like the head and foot. Shop drawing: bedlights-boards.html#trim.

have ithave it

Inner back wall, poplar 1x5 ripped to 3 1/2

Have it: Crosscut Hardwoods, bought 2026-09-30 · qty 1

76 7/8 long, 3 1/2 tall, on the deck between the head and foot boards

1 1/4 in in front of the back 1x5. It stands on the deck (the panels run under it), ripped to 3 1/2 (Jeff): its top is 1 in above the outer 1x5's. No LEDs: it carries the wire rail. Shop drawing: bedlights-boards.html#back.

ready to orderstock

Shellac primer and a grey satin enamel

Buy: Home Depot #4013 · qty 1 qt primer, 1 qt paint

Poplar boards, painted grey. Shellac primer (Zinsser BIN) seals poplar's green streaks and raised grain; then a water-based enamel that cures hard (Benjamin Moore Advance or Sherwin-Williams Emerald Urethane), satin.

Before you order: the grey: pick a chip

ready to orderstock

Rubio Monocoat Oil Plus 2C, Pure

Buy: Rockler or Woodcraft (check stock) · qty 1 small set (130 ml)

For the oak front AND the struts' white oak veneer, so they match. One coat, wiped off; it bonds to the wood and needs no build-up. Solvent-free, so it does not attack the veneer's contact cement. Pure keeps white oak light and close to raw.

have ithave it

Black corner braces, 1 1/2 and 2 in, #8 wood screws

Have it: Home Depot #4013, bought 2026-09-30 · qty about 24 braces

#8 x 5/8 into the boards, #8 x 1/2 into the deck: never longer, or it comes through the office ceiling.

Rails

ready to ordercut from stock

LED grooves, routed (if not already)

Buy and cut: router, 1/2 in bit, edge guide

11/16 wide, 5/16 deep, centres 3 1/8 and 2 1/2 up from every board's bottom: one line round the frame

The routing guide has every number.

ready to ordercut from stock

Wire rails: 1/4 x 1/4 groove and the wire holes

Buy and cut: router, 1/4 in bit; drill, 3/16 and 3/8

A 3/16 hole at each run's start to the inside face; a wire groove along the inner back wall's mattress face; a 3/8 crossing hole low in the inner wall for the foot run's lead into the slot.

ready to ordercut from stock

Puck holes and deck grooves

Buy and cut: drill 3/8; router 1/4

A 3/8 hole at each puck and fan; 1/4 grooves in the deck top from each straight back to one cross groove 4 in in front of the inner wall; at its driver end a short groove back under the inner wall (3/8 notch in its bottom edge) into the slot and the junction box.

Slot

have itstock

Spacer strip, 1/2 in ply or poplar

Have it: offcut · qty 1

1 1/8 wide x 1/2 x 76 7/8, on the back strut behind the back panel

The panels are 19 7/8 each (Jeff 2026-10-07), pushed to the front; this fills the gap behind them so the slot floor is level with the deck. Felt on top.

TBDstock

Small black angles, about 1 x 1

Buy: Home Depot #4013 · qty 5

3 in the slot floor (upright on the back 1x5, flat on the strut), 1 in each end corner tying the head and foot boards to it.

TBD until: whether the hardware bag already has them

ready to orderstock

Felt or cork strip for the slot floor

Buy: Home Depot #4013 · qty 1

So a phone or a Kindle does not rattle on the aluminium.

LEDs

have itstock

Aluminium U channel, 16.93 mm wide, black, frosted diffuser, end caps

Have it: Amazon (search) · qty 11 x 1 m

33 ft of channel: two rows on the head, the outer back 1x5 and the foot

The LED rails. Flush in the grooves, nothing in the 1/2 in to the columns.

have ithave it

Warm strip, BTF FCOB 2700K 528/m, 12 V

Have it: bought 2026-08-13 · qty 5.1 m

Top channel. Bare IP30: the channel is its heatsink.

ready to orderstock

RGB strip, BTF FCOB 810/m, 12 V, 4-wire

Buy: Amazon (search) · qty 1 reel (5 m)

Lower channel. One 5 m reel does the bed.

orderedstock

Strip-to-wire clips, 10 mm 2-pin COB (warm strip)

Buy: Amazon, VISDOLL, bought 2026-10-11 · qty 20

The warm strip's corners: one clip each side of the cut, a wire between. Check the strip is 10 mm wide.

ready to orderstock

Strip-to-wire clips, 10 mm 4-pin RGB COB, with 10 ft 22 AWG 4-core

Buy: Amazon, PAUTIX · qty 20 + 10 ft · $23.39 with the coupon

The RGB strip's corners, and the 4-core for the jumpers and the strip lead. 10 mm inside (the 12 mm in the listing is the clip's length).

ready to orderstock

Strip leads: 22 AWG, 2-core and 4-core

Buy: Amazon (search) · qty about 15 ft each

Clip or solder to each strip's start, through the hole, into the junction box in the slot. The PAUTIX kit's 10 ft covers the RGB; any red/black 22 AWG for the warm.

ready to orderstock

Aluminium foil tape

Buy: Home Depot #4013 · qty 1 roll

Over the wire groove and the deck grooves, so the mattress cannot snag a wire.

Pucks

ready to orderstock

Slim 12 V surface pucks, 2700 to 3000K, 3/8 or thinner

Buy: Amazon (search) · qty 4

about 2 3/4 across, 3/8 thick

The office lights when the bed is up: a near-square grid under the deck.

Before you order: under 3/8 thick so nothing pushes into the mattress

have ithave it

Caframo Sirocco II 12 V gimbal fans, x2

Have it: Jeff's (confirm the second is in hand) · qty 2

about 7 1/4 across, about 2 deep folded

One under each front corner, angled in (Jeff, 2026-10-12). Channels 7 and 8, on and off only: their own buttons set the speed and timer. Set both channels to switch fully on, never dim them. If one comes on off after power returns, press its button once.

Wiring

ready to orderstock

Junction box in the slot, printed, with Wago 221 lever nuts

Buy: Home Depot #4013 (Wagos); P1S, PETG (box) · qty 1 box; 6 x 221-415, 7 x 221-412, 4 x 221-413

9 x 1 1/8 x 2 1/4 outside, in the back slot's driver end

Every strip, puck and fan lead meets the cable here. Drawing: overview, Wiring, The junction box.

ready to orderstock

Drag chain, 10 x 15 mm inside, about 4 ft

Buy: Amazon (search) · qty 1

In the rear driver corner, behind the back Happijac column: hanging in a U along the driver wall that follows the bed.

Before you order: the corner pocket fits the chain's U (about 2 1/2 along the wall, 1 in from wall to bed)

ready to orderstock

Continuous-flex cable, 12-core, 18 AWG, about 27 ft

Buy: Amazon (search) · qty 27 ft

Drag-chain rated. Three cores paralleled for +12 V: one 18 AWG core alone drops too much over this run (see the plan).

ready to orderstock

Cable clips and grommets

Buy: Home Depot #4013 · qty 1 bag

orderedstock

QuinLED An-Penta-Deca controller (ESP32)

Buy: DrZZs (US), ordered 2026-10-12, order 93043 · qty 1 · $49 + $6.50 shipping

Ships with WLED on it: start there to test and run the lights; ESPHome later swaps the software only, no rewiring. 15 channels, 5 A each, 12 to 48 V, external antenna, 4 x 4 x 1 in. Eight channels for the bed: warm, red, green, blue, pucks white, pucks red, fan 1, fan 2. The rest stay free for the truck's other lights. Wiring diagram: overview, Wiring.

ready to orderstock

Lights A fuse (20 A, at the DC box) and master rocker A

Buy: Amazon (search) · qty 1

The fuse at the DC box end of the 12/2 feed (it protects the wire); the rocker on the control box's face. QuinLED A also runs the garage and the outdoor light: lighting-overview.html.

ready to orderstock

12/2 tinned duplex, DC box to the control box (Lights A)

Buy: Amazon (search) · qty the run

+ through the fuse at the bus; - to the bus negative on the load side of the SmartShunt, so the shunt counts the lights.

Before you order: how far the control box is from the 12 V bus

ready to orderstock

Wireless remote for the bed, WiZmote (ESP-NOW)

Buy: Walmart or eBay (about $10 to $16) · qty 1

In a holder in the lounge. WLED hears it directly over ESP-NOW (no WiFi, no hub); a Shelly BLU would need ESPHome or a hub.

TBDprinted

Control box, printed cover

Print: P1S, PETG · qty 1

In the aft kitchen upper: controller, fuse, switch.

TBD until: the controller in hand

Headboard

ready to orderstock

Headboard panel, 1/2 in ply

Buy: Home Depot #4013 · qty 1 (a 2 x 4 sheet)

55 3/4 x 13 1/2, 1/2 in: veneered both faces

Stands on the head board's full-height stretch, 14 above the mattress. Shop drawing: bedlights-boards.html#headboard.

have ithave it

White oak veneer for the headboard, both faces, and contact cement

Have it: left from the struts' veneer · qty 2 pieces, about 57 x 15

Both faces, so the panel stays flat; oiled to match the struts and the oak front.

have ithave it

Matte black hinges, 1 1/16 x 12 in

Have it: bought 2026-09-30 · qty 4

Knuckle on the head board's inboard top edge: the headboard can only fold forward onto the mattress.

ready to orderstock

Locking lid supports, matte black

Buy: Home Depot #4013 · qty 2

One each end, inboard: they click rigid when it is upright, so it cannot fold onto you in the night.

Before you order: where the lower bracket goes (see the questions)

TBDstock

Travel hold for the folded headboard (to decide)

Buy: not picked yet

Bed up, the folded headboard sits 1/2 under the ceiling and cannot lift. Bed down, it lies on the mattress with nothing rigid to catch on.

TBD until: how it is held folded: see the questions

Tap a card to find it here. Tap a part to find its card.